architecture - engineering - construction
AECinfo.com
Printable version Bookmark this page Notify a colleague or friend about this page Bookmark and Share
  Bobrick Washroom Equipment   Toilet Partitions  

Toilet Partitions - Page 3

   

Toilet Partitions

Toilet Partitions 

 

DuraLine Series is engineered of solid phenolic for impact-and water-resistance

  1. Stiles and doors: ¾" (19mm) thick solid phenolic; panels ½" (13mm) thick.
  2. Solid phenolic core with multiple resin-impregnated kraft, color and clear Melamine surface sheets fused at high temperature and pressure. Edges are polished black phenolic. Warranted for 10 years against delamination, corrosion or breakage when properly installed, used and serviced.
  3. Two 3/8" (10mm) diameter threaded rods secure stile to floor or ceiling. One-piece, satin-finish stainless steel shoe conceals leveling device. Patent pending.
  4. 3/16" (5mm) thick, corrosion-resistant, chromate-treated, double zinc-plated steel angle leveling bar is secured to base of solid phenolic stile.

TrimLine and Designer Series feature steel core strength and durability

  1. 11-gauge (3mm) steel core reinforcing plate is welded to the steel leveling bar, forming a single structural unit. Panel-to-stile mounting bracket screws are secured into the steel core which carries the load and impact on panels, stiles and doors into the building structure.
  2. 3-ply, 45 lb. density, resin-impregnated particle board core is impact- and warp-resistant; stabilizes stiles, doors and panels.
  3. Laminated plastic edges applied first, then broad surfaces to seal in the edges (Designer Series); resists vandals’ attempts to pry edges off. Stiles, doors and panels are 1" (245mm) thick.
  4. Two 3/8" (10mm) diameter threaded rods secure stile to floor or ceiling.
  5. 3/8" (10mm) thick steel leveling bar. One-piece, satin-finish stainless steel shoe conceals leveling device. Patent pending.

 


FLOOR ANCHORED

Recommended for high ceiling washrooms, provides a clean line across top of partitions. Furnished with sleeve anchors that require minimum 2" (51mm) penetration into 3" (76mm) thick structural concrete floor. (1041 Floor-Anchored Designer Series pictured.)

 

Description
Stainless Steel Edge 
Laminated Plastic Edge 
Solid Phenolic 

Series No.
1031 
1041 
1081 


THREADED INSERTS. Mounting holes for door hinges and latch are factory drilled and furnished with threaded inserts. Metal-to-metal contact at hinge and latch attachments provide maximum holding power; installation time and costs are reduced. Threaded inserts and mounting screws used in 1" (25mm) thick particle board core of TrimLine and Designer Series partitions have been tested and were found to withstand a direct pull of over 675 pounds for hinge attachments, 950 pounds for latch attachments. Inserts used in the ¾" (19mm) thick solid phenolic DuraLine Series were tested and found to withstand a direct pull of 1000 pounds. For description of lab test, ask for Bobrick Advisory Bulletin TB-34.

 

THREADED INSERTS secure hinges on Trimline and Designer Series.

T-NUTS secure door latch on TrimLine and Designer Series.

CONCEALED THREADED INSERTS for Commercial hardware and .67 option institutional door hardware on Duraline Series.


FLOOR ANCHORED

Furnished with sleeve anchors that require minimum 2" (51mm) penetration into 3" (76mm) thick structural concrete floor. Please refer to Bobrick Advisory Bulletin TB-46 for Recommended Mounting Systems for Floor-Anchored Partitions. 



Request for Information / Request a Catalog from Bobrick Washroom Equipment
 
 
 
To request more information from Bobrick Washroom Equipment, please complete the form below.
 
*Name:    
*Email:    
Company:    
*Type:    
Phone:    
*Address:    
*Request:    
    (* = Mandatory field) 
Please add me to the mailing list for the free monthly e-Newsletter AECnews.