|
|
Bobrick Washroom Equipment
Mirrors
Mirrors - Page 1
Mirrors
Mirrors
|
B-290 SERIES FRAMED MIRRORS One-piece roll-formed frame is ¾" x ¾" (19x19mm), type-304 stainless steel angle with satin
finish. Special bevel design hugs mirror. Corners are heliarc welded, ground and polished smooth. No. 1 quality, ¼" (6mm) glass
mirror electrolytically copper-plated; guaranteed against silver spoilage for 15 years. Mirror edges protected with plastic filler strips to
prevent chipping; back is protected by 3/16" (5mm) thick, water-resistant, polyethylene padding. Galvanized steel back attached to
frame with concealed screws. Secured to concealed wall hanger (shown below) with two theft-resistant locking screws.
STANDARD SIZES B-290 SERIES MIRROR
Model No. |
Width |
Height |
|
B-290 1218 |
12" |
18" |
(30x46cm) |
B-290 1624 |
16" |
24" |
(41x61cm) |
B-290 1824 |
18" |
24" |
(46x61cm) |
B-290 1830 |
18" |
30" |
(46x76cm) |
B-290 1836 |
18" |
36" |
(46x91cm) |
B-290 2060 |
20" |
60" |
(51x152cm) |
B-290 2430 |
24" |
30" |
(61x76cm) |
B-290 2436 |
24" |
36" |
(61x91cm) |
B-290 2448 |
24" |
48" |
(61x122cm) |
B-290 2460 |
24" |
60" |
(61x152cm) |
B-290 2472 |
24" |
72" |
(61x183cm) |
B-290 3636 |
36" |
36" |
(91x91cm) |
B-290 4830 |
48" |
30" |
(122x76cm) |
B-290 4836 |
48" |
36" |
(122x91cm) |
B-290 6030 |
60" |
30" |
(152x76cm) |
B-290 6036 |
60" |
36" |
(152x91cm) |
B-290 7236 |
72" |
36" |
(183x91cm) |
Special-order sizes available on request. Maximum size of one-piece mirror: 144" x 72" (366 x 183cm). Maximum frame size available: 186" x 72" (472 x 183cm) with two pieces of glass in one-piece frame furnished with I-section molding with polished stainless steel exposed finish covering seam where two pieces of glass butt together. Shelves longer than 120" (305cm) will be furnished as two pieces butted together. To specify special sizes, use Series Number followed by width and height in inches. For example: B-290 70 x 30 (178 x 76cm) or B-292 132 x 48 (335 x 122cm).
CONCEALED WALL HANGERS FOR THEFT-RESISTANT MOUNTING Simplifies installation. Mirror is held flush to wall by integral brackets at top and by two locking devices on bottom corners of mirror back. Constructed of galvanized steel. Furnished with B-290 Series Framed Mirrors and B-292 Series Mirror/Shelf Combinations. Note: Provide minimum ¾" (19mm) clearance at top of mirror for mounting on wall hanger, minimum 1" (25mm) clearance at bottom for engaging locking screws, and 1" (25mm) clearance on each side.
DESIGNER'S NOTES
To specify mirrors, use Series Number desired followed by width and height in inches. Width dimension must always be stated first following
Series Number. B-165, B-290, B-293, and B-294 Series mirrors must be installed with width and height dimensions as ordered. Mirror back
and wall hanger cannot be installed side ways to reverse width and height dimensions.
