| INSTALLATION Surface should be properly sloped to drain freely and eliminate the
ponding of water. The surface must be clean, dry and free of laitance, dirt, oil, grease
or other contamination.
SURFACE PREPARATION: Plywood shall be
3/4" minimum thickness, A/C or better, exterior grade tongue and groove type. Install
with A side up.
Design deck to eliminate vertical deflection by proper
selection of plywood thickness and spacing of supports. All plywood edges must be
supported on blocking or primary framing. Fasten with non-corroding screws, 10d annular
ring or twist shank nails. Space fasteners 6" on center along panel edges and
12" on center over intermediate supports.
Plywood panels shall be butted flush with adjoining panels.
Sand as required to provide a flush surface. All adjacent metal flashing, scuppers, vents,
etc. shall be galvanized or non-ferrous metal, tightly screwed or nailed with ring shank
nails no greater than 4" on center.
Sweep all joints clear of debris and sawdust. Fill all
separations over 1/16" wide with CCW-102C or CCW-201 Sealant. Apply joint
reinforcement consisting of a coat of CCW-501-T Detail Coat, 30 mils thick, 5" wide
centered over all joints and transitions to metal flashings, drip edges, etc. Embed CCW
Fiberglass Reinforcing Tape into the wet membrane.
Apply a 1" face, 45 degree cant of sealant at all
angle changes, including projections through the deck, walls, etc. Allow sealant to cure
thoroughly. Allow the stripe coat to cure over night (16 hours minimum). Caution:
ensure that all sealant is thoroughly cured. Uncured sealant may effect the cure of the
coating.
PRIMING: Priming with CCW-557 Primer
is recommended. OSB must always be primed. Consult with the Carlisle representative before
deciding priming is not required. Stir each side separately to ensure that no separation
has occurred then mix all of Part A with all of Part B. Use a mixing paddle in a slow
speed electric drill motor. Avoid air entrapment. Mix 2 to 3 minutes until a homogenous
blend is achieved. Wait 15 minutes before applying.
Apply primer at a rate of 300 square feet per gallon. Avoid
puddles or ponding the primer and do not apply primer over stripe coats.
Allow primer to dry for 1 hour minimum, 8 hours maximum.
Primer is sufficiently dry when it is somewhat tacky but will not transfer when touched.
In the event coating is not applied within the maximum time, reprime.
BASE COAT APPLICATION: Do not apply
coating over joints greater than ½" wide. Wipe stripe coats to remove any dust or
contamination. Apply CCW-501 in one uniform coat at the rate of one gallon minimum per 50
square feet or as needed in order to obtain a minimum thickness of 32 wet mils.
Backroll for even coverage. Allow the base membrane to cure 16 hours minimum at 75ºF.
INTERMEDIATE COAT APPLICATION: (
Recommended for all except small, light duty applications.) Apply CCW-502 in one uniform
coat at the rate of one gallon minimum per 100 square feet or as needed in order to
obtain a minimum thickness of 16 wet mils. Immediately broadcast 30-65 mesh silica sand
into the wet CCW-502 at a rate of 25 lbs. per 100 sq. ft. Allow to cure 16 hours
minimum at 75ºF. Sweep or vacuum off excess sand.
TOP COAT APPLICATION: Apply CCW-503 in one
uniform coat at the rate of one gallon minimum per100 square feet or as needed in order to
obtain a minimum thickness of 16 wet mils. Backroll for even coverage. Allow the CCW-503
to cure at least 48 hours before opening the deck to traffic.
LIMITED WARRANTY
CARLISLE COATINGS AND WATERPROOFING INCORPORATED (CARLISLE)
warrants this product to be free of defects in workmanship and materials only at the time
of shipment from our factory. If any CARLISLE materials prove to contain manufacturing
defects that substantially affect their performance, CARLISLE will, at its option, replace
the material or refund the purchase price.
This limited warranty is the only warranty extended by
CARLISLE with respect to its materials. There are no other warranties, including the
implied warranties of merchantability and fitness for a particular purpose. CARLISLE
specifically disclaims liability for any incidental, consequential, or other damages,
including but not limited to, loss of profits or damages to a structure or its contents,
arising under any theory of law whatsoever.
The dollar value of CARLISLE'S liability and buyer's remedy
under this limited warranty shall not exceed the purchase price of the CARLISLE material
in question.
| Carlisle is a
trademark of Carlisle Corporation ©1998 Carlisle
Corporation
CCW-5123 1/98 pb |
 |
Carlisle Coatings
& Waterproofing Incorporated Subsidiary of Carlisle Corporation P.O. Box 1600, Sapulpa, OK 74067-1600.
Telephone: 1-800-338-8701
Website:www.carlisle-ccw.com |
|
