 |
CCW-701
SHEET MEMBRANE WATERPROOFING SYSTEM |
DESCRIPTION
The CCW-701 Sheet Membrane Waterproofing System consists of
a 56 mil thick rubberized asphalt membrane which is laminated to high density 4 mil
polyethylene film on the face and siliconized release sheet on the adhesive side.
The sheet membrane is available in two convenient widths of 36" and 48". The
system offers a variety of primers featuring both solvent based and water based formulas.
The system provides a non-sag mastic for sealing terminations of the sheet membrane. The
factory controlled thickness assures uniform thickness on the job while the inherent
waterproofing properties of the rubberized asphalt and the polyethylene film provide an
excellent water barrier.
TYPICAL USE
The CCW-701 Sheet Membrane Waterproofing System is suitable
for a wide variety of applications such as waterproofing of below grade foundation walls,
earth shelters and tunnels. The system is also suited for waterproofing between the
structural slab and wearing course on parking decks, mud slabs, terraces, balconies,
equipment rooms, kitchens, bathrooms, and laboratories. The system is also used on wood
structures to provide water proofing protection.
LIMITATIONS
- Not recommended in areas where membrane will be subject to
continuous exposure to sunlight
- Do not apply primer or membrane to frozen concrete.
- Optimum results are obtained when membrane is installed at
temperatures above 25º F. Between 25º F and 40º F use CCW-701 LT Low Temperature
membrane and CCW-702 LT Primer. CCW-701 LT can be used up to 60º F.
- Do not apply primer or membrane to a damp, frosty or
contaminated surface.
- Not recommended as a pond or tank liner except for
"between slab" applications.
- Not recommended for use over sealants containing coal tar or
polysulfides. In the event of existing bitumen modified materials, consult the Carlisle
representative.
APPLICABLE STANDARDS
CCW-701 meets the applicable requirements of:
- GSA; PBS PCD 07121
- USN; NAVFAC TS-07111
- VA; H-08-1
- Federal Construction Guide Specs; FCGS-07111
- Cord of Engineers; CEGS-07111-3-82
- UL790, ClassA
PACKAGING
CCW-701-36 = 36" wide X 67' roll (200 ft2)
25 rolls per pallet (5000 ft2) - Weight = 82 lb/rl (approx)
CCW-701-48= 48" wide X 50' roll (200 ft2)
25 rolls per pallet (5000 ft2) - Weight = 84 lb/rl (approx)
Other membrane thicknesses and configurations are available
by special order.
CCW-702 Solvent Based Primer:
5 gallon pails (45 pails per pallet)
CCW-702 LT Low Temperature Primer:
5 gallon pails (45 pails per pallet)
CCW-714 Water Base Primer:
5 gallon pails (45 pails per pallet)
CCW-704 Mastic
30 oz. Qt. Cartridge (12 ctg. per case), 5 gallon pails (45
pails per pallet)
TECHNICAL DATA
| PROPERTY |
TEST
METHOD |
RESULTS |
| Tensile |
D 412(C) Mod. |
300 psi |
| Elongation* |
D 412(C) Mod. |
300% (min) |
| Permeance |
E 96 (B) |
.05 perms |
| Low Temp. Flexibility |
D 1970 |
Unaffected @ -45ºF |
| Crack Cycling (100 cycles) |
C 836 |
Unaffected @ -25ºF |
| Peel Strength |
D 903 |
7.5 lb/in. width (min.) |
| Lap Adhesion |
D 1876 Mod. |
7.0 lb/in. width |
| Puncture Resistance |
E 154 |
40 lb. (min) |
| Exposure to fungi |
GSA-PBS 07115 |
16 wks, no effect |
| H20 Absorption |
D 570 |
0.1% by wt. (max) |
| Hydrostatic head |
D 5385 |
231 ft. (min.) |
| % of elongation to ultimate
failure of rubberized asphalt membrane |
WARNINGS AND HAZARDS
CCW-702, CCW-702 LT and CCW-704 contain flammable and con
combustible solvents. Avoid exposure to open flame. Avoid breathing vapors. Use only in
areas with adequate ventilation. Refer to MSDS for important warnings and product
information. |
