TECHNICAL DATA
| PROPERTY
RESULTS |
ASTM |
|
| HIGH PROFILE CORE |
|
|
| Thickness |
D-1777 |
1.0 in. |
| Compressive Strength |
D-1621 |
12,000 psf |
| Flow Rate |
D-4716 |
100 gpm/ft |
| SHEET DRAIN CORE Thickness |
D-1777 |
0.25in. |
| Compressive Strength |
D-1621 |
15000 psf |
| Flow Rate |
D-4716 |
16 gpm/ftw |
| FABRIC |
|
|
| Grab Tensile |
D4632 |
|
| Flow Rate |
D-4491 |
170 gpm/ft |
| AOS |
D-4751 |
80 |
| Weight |
D-3776 |
4.0 oz/yd2 |
| Permeability |
D-4491 |
0.20 cm/sec |
| Puncture Strength |
D-3787 |
70 psi |
PACKAGING
Roll Length: 50 ft.
Roll Width: 2 ft.
Roll Weight: 50 Ibs.
Connectors, pipe adapters and corner fittings are available
to complete the system.
INSTALLATION
SURE-DRAIN and TOTAL-DRAIN products can be attached to CCW
waterproofing membranes with double sided adhesive tape or construction adhesives. Discuss
material compatibility with Carlisle representatives before using adhesives.
Install the TOTAL-DRAIN section first, with the thinner
transition section up and the geotextile filter fabric out. carefully seal all
joints, corners and transitions to drainage system discharge pipes immediately to prevent
soil from entering the system.
If weep holes or discharge pipes in the wall are used
instead of a drain pipe, cut a hole in the core at these locations; do not cut
fabric. On the soil side of the drain, bridge the cutout area with a plate 4 to 6
inches larger than the cutout to prevent soil breakthrough.
Attach the next course of SURE-DRAIN Drainage Composite to
the the transition section. Place the lower edge of next panel (edge without a flange)
overlapping the flange of the previously installed panel. Overlap the fabric in the
direction of the water flow.
Add additional sections of SURE-DRAIN Drainage Composite as
required, working up the wall from the lowest section to the highest. Make all overlaps of
core and fabric edges in a shingle fashion so that water flows in the same direction as
the overlap. If necessary, use tape or spray adhesive to keep fabric in place prior to
backfilling. To attach the end of a roll of drain to the beginning of the next, peel back
filter fabric and overlap two rows of dimples. Press to interlock the panels, then pull
the fabric back over the joint, overlapping both in the direction of expected water flow.
All terminating edges of the drainage composite should have
extra fabric tucked behind core to seal the edge and prevent soil from entering the core.
If perimeter drainage only is required, TOTAL-DRAIN-P
should be used. This version features the same drainage core as standard TOTAL-DRAIN, but
with the filter fabric sealing both the top and bottom edges of the core. This prevents
soil from entering the core when used as a stand-alone section without SURE-DRAIN
wall drainage composites
STORAGE
Protect material from excessive heat and cold. Store
materials away from open flame, sparks, or welding. For outside storage, protect materials
from direct sunlight, rain or other harmful environmental conditions.
LIMITED WARRANTY
CARLISLE COATINGS AND WATERPROOFING INCORPORATED (CARLISLE)
warrants this product to be free of defects in workmanship and materials at the time of
shipment from our factory. If any CARLISLE materials prove to contain manufacturing
defects that substantially affect their performance, CARLISLE will, at its option, replace
the material or refund the purchase price.
This limited warranty is the only warranty extended by
CARLISLE with respect to its materials. There are no other warranties, including the
implied warranties of merchantability and fitness for a particular purpose. CARLISLE
specifically disclaims liability for any incidental, consequential, or other damages,
including but not limited to, loss of profits or damages to a structure or its contents,
arising under any theory of law whatsoever.
The dollar value of CARLISLE'S liability and buyer's remedy
under this limited warranty shall not exceed the purchase price of the CARLISLE material
in question.
| Carlisle is a
trademark of Carlisle Corporation ©1998 Carlisle
Corporation
TOTAL-DRAIN 11/98 pb |
 |
Carlisle Coatings
& Waterproofing Incorporated Subsidiary of Carlisle Corporation P.O. Box 1600, Sapulpa, OK 74067-1600.
Telephone: 1-800-338-8701
Website:www.carlisle-ccw.com |
|