CHEMSTONE PRODUCTS

BONDERIZER FORMULA
    RETARDANT

TILE THINSETS - SWIMMING POOLS STUCCO - CONCRETE BLOCK PONDS - PLASTER

Under excessive heat condition and dry temperatures, we recommend using Bonderizer Formula Retardant for all thinsets and other products that incorporate a cement sand mixture.

BONDERIZER FORMULA:

Is an acrylic latex composition compounded with BERYLEX  Liquid Concentrate to provide greater density, waterproofing, better color retention, non-shrinking, with exception bond strength, for thinsets, stucco, plaster, concrete, porcelain type tiles, marble, swimming pools, wood, glass and over existing tiles with thinsets.

SURFACE- PREPARATION:

Use HID (Heavy Industrial Dissolvent) first to remove oils, wax, grease, black asphalt mastic or any other contamination. Follow with Allzup as per label.

FOR ETCHING SMOOTH CONCRETE SURFACE:

For better bonding, dilute Allzup 1 part with 1 part water. Disperse this over area and let stand until liquid dries to white powder. Rinse off with water.

BONDERIZER FORMULA SOLUTION:

Stir contents thoroughly. Dilute 1 part Bonderizer Formula with 2 parts clean water and stir again. Use Bonderizer Formula diluted as above as only wetting agent for all tile thinsets, stucco, plaster concrete mixes and swimming pool coatings.

BONDING NEW CONCRETE TO OLD:

Blend 3 parts sand to 1 part cement for floors. On walls add 1 part lime. Use the above Bonderizer Formula solution as the only wetting agent. Use no other water.

1. In a separate container pour a desired amount of Bonderizer Formula full strength.

2. To this add dry cement and stir to a brushable solution.

3. Brush this over the pre-wet area, while still damp apply the pre-mix concrete.

4. Level cut to the desired thickness. It can be troweled down to the existing surface. It will not peel or crack. Damp cure when complete.

TO RESET LOOSE TILES:

1. Clean area as outlined in surface preparation.

2. Use Bonderizer Formula solution for thinset.

3. Pre-wet area to be patched. While still damp, apply brushable slurry coat.

4. Back butter each tile with thinset mix and place in position. Tamp down to a flush surface.

TILING OVER TILE:

1. Clean area well, as outlined in surface preparation. This will produce a chemically clean bondable surface. Mix thinset with Bonderizer solution.

2. Spread over existing tile with a 1/2" notch trowel.

3. Set tiles and use BERYLEX 44-T as the only wetting agent for the grout.

4. Damp cure.

BONDING TILES TO PLYWOOD:

1. Make sure plywood is nailed down securely. Check floor for possible flexing. If any, shore up from underneath if needed.

2. Seal and waterproof plywood, wallboard, particle board, or backer board with Terra Matt prior to tiling.

TILING OVER WOOD WITH BONDERIZER SOLUTION THINSET:

1. Lay 20 lb. felt over wood floor, overlap at seams, and staple down.

2. Lay metal lath on top of 20 lb. felt. Staple down. Drive all staples flat to metal lath.

3. Make up Bonderizer and thinset mix to workable consistency.

4. With straight edge of trowel, apply thinset to metal lath. Trowel down flush to existing metal lath.

5. When setting bed is dry, use a 1/2" notch trowel to apply a thinset mix with Bonderizer Formula over existing prefloated cement bed.

6. Set tiles in the float mix. Use beating block to set tiles to a level finish.

7. Grout with BERYLEX 44-T in grout mix. Damp cure.

PLASTER AND STUCCO:

1. Use only the diluted Bonderizer formula as the wetting agent for the dry mix in each application, brown coat and finish.

2. This process will minimize shrinking, color fading, as well as waterproofing.

3. Will give greater bonding strength to existing surface, wire mesh, metal laths, etc.

4. Damp cure after each application.

SWIMMING POOL COATINGS:

Use Bonderizer solution in all mixings of color coat on pool area. Damp cure for 2 .days. Will minimize color fading and shrinkage.

Is used to make BETTER concrete - Not to replace cement BERYLEX cannot correct human errors or man failures.