AQUA FLASH 500
A 40 mil sheet type flashing membrane consisting of 8 mils of a high density cross
laminated polyethylene film bonded to 32 mils of highly adhesive rubberized asphalt
with a silicone coated release liner.
AQUA FLASH 500
Product Description:
AQUA FLASH 500 is a self sticking flashing with the following features:
Self-sealing
Self-healing if damaged somewhat due to the rubberized asphalt's ability to elongate
and recover
Excellent puncture resistance
No reglet needed when adhering membrane to vertical substrate
Uses:
AQUA FLASH 500 is ideal for use as:
Thru-Wall Flashing
Concealed Flashing
Foundation Sill Flashing
Base Flashing
Spandrel Flashing
Head and Sill Flashing
Parapet Flashing
Installation:
AQUA FLASH 500 should be cut into 8-10 foot lengths. Remove the release liner and
apply membrane to substrate. Once membrane is in place, use a steel hand roller to
firmly secure flashing. All side laps should be a minimum of 2-1/2 inches. Inside and
outside corners must be covered with two layers of membrane and sealed with AQUA
FLASH mastic.
Sizes: AQUA FLASH 500
Standard Width 12" 18" 24" 36"
Standard Length 50 LF
When necessary, AQUA FLASH 500 can be applied as part of a system which uses
both the AQUA FLASH mastic and AQUA FLASH primer.
AQUA FLASH Mastic
Product Description: AQUA FLASH Mastic is a highly rubberized asphalt adhesive
used in conjunction with the AQUA FLASH membrane
Use: Seals all horizontal terminations, seams, laps, protrusions, accidental cuts or
punctures
AQUA FLASH Primer
Product Description: AQUA FLASH Primer is a water based adhesive used in
conjunction with the AQUA FLASH membrane
Use: If the substrate is not dirt free, or the membrane will not adhere properly.
Installation: Spray, roll or brush apply AQUA FLASH Primer at a rate of 200-300
square feet per gallon. Dry until tack free and cover with AQUA FLASH membrane
within 24 hours.
Technical Data Table - Aqua Flash 500
Property |
Average
Values |
Test
Method |
MVT |
0.05 grains
max/sq. ft/hr.
in HG |
ASTM E96
Method B |
Water
Absorption |
.1% by weight,
Max.to -45°F
no crack
or peel
|
ASTM D570 |
Pliability at 180°F
over 1/2" Mandrel |
ASTM D146 |
Peel Adhesion (Dry) |
7.0 Ibs/in., min |
ASTM D903 |
Pool Adhesion (Wet) |
5.0 lbs./in., min. |
ASTM D903 |
Lap Adhesion
at 25°F |
5.0 lbs./in., min. |
ASTM D1876 |
Elongation |
300% |
ASTM D412 |
Tensile
Strength |
1500 psi |
ASTM D412
(Die C Modified) |
Puncture
Resistance |
40lbs., min. |
ASTM E154 |
Film |
170lbs., min. |
ASTM D781 |
Tear Resistance |
Propitiation MD |
12.18 lbs. |
ASTM D1938 |
Initiation MD |
13 lbs. |
ASTM D1004 |
PRODUCT INFORMATION
Marking:
Rolls are marked with manufacturer's trade name for positive on site identification.
Technical Data
Fiberweb and Fiberweb Tapes are tested in accordance with ASTM testing
procedures. See Tables for technical data. The values shown in the Tables are
average values.
Availability
Fiberweb and Fiberweb Tapes are available through the distributor listed below.
Cost
Fiberweb offers superior performance at very competitive prices. For current costs
contact the distributor.
Limited Warranty
Hammerbeam Inc. warrants that Fiberweb products meet the specifications listed
herein, and that they are tested to assure conformance to the physical properties
listed in the attached Technical Data Tables. Hammerbeam Inc. is not responsible
for damage caused by improper use, installation or handling.
THE FOREGOING WARRANTY IS ALL INCLUSIVE AND IS IN LIEU OF ALL
OTHER WARRANTIES WHETHER WRITTEN, ORAL, EXPRESSED OR IMPLIED
INCLUDING ANY WARRANTY OF MERCHANTABILITY FOR PURPOSES OTHER
THAN THOSE ADVERTISED OR DEPICTED HEREIN OR WARRANTY OF
FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL
HAMMERBEAM INC. BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING FROM ITS USE.
Technical Services
Technical advice and additional information may be obtained by writing or calling
the manufacturer.. |
Technical Data Table - Aqua Flash 500 Primer
Property |
Average
Values |
Solvent Type
|
Water |
Application
Temperature |
25 degrees
Fahrenheit
and over |
Flash Point |
Non
Combustible |
VOC Content |
None |
|
Fiberweb Corp. Div.