Friedrich
VERT-I-PAK™ eliminates the need for split systems or multiple PTACs.
A Unique Product
VERT-I-PAK '" is a self contained air
conditioner designed for quick installation and easy access. It is compact enough to be
placed in a small closet on either side of a room. (See front cover.) An access panel or
door allows for easy maintenance or removal of the unit. And since VERT-I-PAK'" is a
self contained unit, certified HVAC technicians arc not required for installa tion and
basic maintenance.
The unit receives fresh air and discharges air
through an architectural louver mounted in the outside wall and attached to the unit with
an adjustable wall plenum. Standard 10" ductwork attaches to the top of the unit and
runs through prebuilt soffits. Multiple diffusers can be placed as required.
Advantages
- Far more cost effective than split system or multiple
PTACs
- No outside condensing units,eliminating the need for
landscaping and vandalism barriers
- No refrigerant linesruning from floor to floor
- Far quieter than PTAC units
- No need for costly finished wall sleves,wiring kits or
decorative fronts
- Rustproof, polysterene drain pan,shroud and condensor fan
- Long-life ball bearing motor
|
VERT-I-PAK'" COMES EQUIPPED WITH:
• 230/208V power cord
• 2 speed fan
• Single direct drive motor for
ultra-quiet operation
• Slinger ring condenser fan for maximum
condensate disposal and energy efficiency
• Cooling mode freeze protection
• Adjustable left or right drain
connections
• Remote thermostat-ready 24V transformer
• Quick-release power disconnect
• Sound insulation package
• Seacoast protected coils available
VERT-I-PAK"' heat pumps and heat/cool
units are available in 9,000, 12,000 and 18,000 BTU capacities with 2.5 KW, 3.4 KW and 5.0
KW electric heat options. VERT-I-PAK'" is also available in cooling only
configurations.
1 ARCHITECTURAL LOUVER • VPAL I Extruded
aluminum grille that attaches to the outdoor section of the wall plenum. Takes in fresh
air and returns condensed air. Can be ordered in custom colors.
Dimensions: 25 9/16" Wx 31 1/16" H
2 WALL PLENUM • VPWPI, VPWP2 Two-part
sleeve that telescopes in and out. Sits inside the exterior wall penetration.
VPWP I telescopes from 4 l/2"-8"
VPWP 2 telescopes from 8"-14"
Dimensions: 24 1/8" Wx 30 3/8" H
Cutout dimensions: 24 5/8" W x 30 7/8" H
3 RETURN AIR GRILLE/ACCESS PANEL • VPRG I
Serves as an access panel to the chassis and interior return air grille. A field-supplied
(12" x 20") filter is mounted inside the grille.
Dimensions: 30" Wx 50" H Cutout
dimensions: 28 1/4" Wx 48 1/4" H
4 RETURN AIR GRILLE •VPRG2 nterior return
air grille that hinges to allow a field-supplied (16" x 20") filter to slip
inside. Must be used when an access door/ panel already exists in closet.
Dimensions: 22 3/8" W x 18 7/16" H
Cutout dimensions: 20 1/2" W x 16 1/2" H
5 FILTER BRACKETS • VPFB I Brackets allow
field-supplied (16" x 20") filter to be attached directly to the unit's chassis.
6 SINGLE STAGE THERMOSTAT-VPRT I Honeywell 24
Volt wall mounted thermostat. (Single stage heat and cool). 24 Volt transformer is factory
installed into all chassis.
|
