MODEL DESIGNATION

FEATURES

HASTINGS Air Cooled Condensing  Units have been designed to offer a complete family of units to cover high temperature air cooled condensing unit requirements from 3 through 80 tons. Polyphase  fan motors are used for high reliability and minimum maintenance. Fans are aluminum bladed, direct drive, and selected for minimum noise. Compressors are matched to condensers for optimum efficiency.

CABINET is constructed entirely of mill galvanized sheet steel panels and formed steel channel base. All panels are removable for access and service.

MOTORS are three phase, 1140 RPM, specifically designed for vertical shaft, direct drive fan application and utilize permanently lubricated ball bearings. Corrosion resistant  steel rod mounting brackets reduce air turbulence and eliminate   vibration.

FANS are direct drive propellor type with steel hubs and aluminum blades. Vertical air discharge through a formed venturi minimizes noise generation and air recirculation.

CONDENSER COILS are constructed with seamless copper tubes arranged in a staggered row pattern and mechanically expanded into plate type configured aluminum fins with full collars. A separate  sub-cooling coil, integral with the condenser, is provided  on each circuit to eliminate the possibility of liquid flashing and to increase unit efficiency.

COMPRESSORS for the "F" Series are full hermetic, direct drive by 2 pole motor, complete with inherent overload protection. Motor Compressor units have internal suspension system to eliminate vibration. Compressors are mounted on rubber shock mounts, and are standard with crankcase heaters.

COMPRESSORS for the "C' Series are accessible hermetic, direct drive  by 4 pole motor, complete with overload protection, automatic reversing, oil  pump,   oil strainer, oil sight glass, suction  and discharge service valves. All Compressors  are mounted on rubber shock mounts, and all have crankcase heaters. Compressor mufflers are standard  for noise elimination.

STANDARD EQUIPMENT

• Direct  Drive Condenser Fans
• Liquid Line Shut Off Valve
• Refrigerant  Charging  Valve
• High Pressure Safety
• Low Pressure Operating Control
• Crankcase  Heater
• Fan Guard
• Auto Pumpdown Switch
• Time  Delay Between Compressors (Dual Units)
• Low Profile
• Sub Cooling Circuit
• Compressor Overload Protection
• Fan Motor Overload Protection
• Fused Control Circuit
• Compressor Contactor
• Fan Motor Contactor
• Removable Access Panels
• Prewired Controls
• Hinged Control Panel Access
• Rigging Points
• Compressor  Service Valves
• Oil Failure Control - "C" only
• Low ambient  operation by fan  cycling to + 20 deg. F.
• Compressor  Fusing (Dual Units)

OPTIONS and ACCESSORIES

• Low ambient operation by fan cycling to ) deg F.
• Low ambient operation  by flood control above 20 deg F (A20).
• Low ambient  operation  by flood control below 20 deg F (B20).
• Liquid line solenoid mounted and wired.
• Liquid line  drier and sight glass mounted.
• High pressure  gauge  with shut off valve.
• Low pressure gauge with shut off valve.
• Oil pressure gauge with shut off valve ('C series only).
• Control circuit  transformer.
• Painted cabinet - Acid etched surface, zinc rich primer and air dried enamel.
• Standard  hot gas  bypass. Includes regulator and solenoid mounted, wired, and stubbed for field connection to the evaporator.
• Capacity modulation by cylinder unloading
• 3 Minute guaranteed off timer for each compressor motor. (Fixed )
• Manual lead lag switch to sequence starting of compressors.
• Low ambient lockout to preset ambient temperature at which the machine will not operate.
• Unit fused discount - mounted, wired and ready for incoming electrical service.
• Contact factory for other options.
• Liquid receiver w/fusible plug.
• Discharge vibrasorber `C' only.
• Suction vibrasorber `C' only

Note: Multiple compressor units are available up to 160 HP, Contact your local Hastings sales representative for information.

In order to maintain or policy of continuous product improvement, we reserve the right to change price, specifications, ratings or dimensions, without notice or obligation.