1. Attach two extruded aluminum side rails to fix-ture housing with the pop-rivets supplied in the hardware envelope. Be sure to line up three holes per side rail (one at each end and the middle) with the three in the housing. The pop-rivets must enter the holes in the direction shown in Figure 1.

GFK Detail

GFK Flange Kit

2. Attach two extruded aluminum end rails to the fixture using the #6-20 x 3/8" long screws supplied. The screws are inserted in the outermost holes of the end rail and fastened into the side rail extrusions. See Figure 2.

 

3. Attach four swing-out hanger assemblies to the sides of the housing using the #8-18 x 5/16" long screws supplied. See Figure 3.

ORDERING INFORMATION

GK Grid Kit

1. Add 1/4" to get ceiling opening.

GK Detail

Plaster frame sets for NEMA F troffers
Parts crimp-lock together for assembly. Minimum ceiling opening to receive plaster frame should be (nominal troffer width) plus 1-1/4" x (troffer row length) plus 1-1/4". Complete sets include necessary side rails, end rails, and corner couplings. Extensions exclude end rails, but include couplings for use with side rails. Order complete sets for individually mounted fixtures. For continuous rows, order one complete set plus one extension set for each additional unit in the row. See individual products for catalog numbers.

Plaster Frames (continued)

Flange Dimensions

Energy/Labor Saving
Master-Satellite Troffer Option

• Reduced number of ballasts required - saves initial and future operating cost
• Polarized plug-in connector reduces installation time and cost
• Flexible whip comes attached to master for easywiring - available in 9' or 11' lengths
• Available in magnetic energy saving or electronicT-8 ballast
• Available in one or three lamp magnetic or one,two, three or four lamp T-8 electronic
• Switching available for applications requiring multi-level switching

ORDERING INFORMATION — Magnetic One and Three Lamp Fixtures

1. For magnetic 1 or 3 lamp fixtures add - MS09 or - MS11 suffix for master unit, - SAT suffix for satellite.

ORDERING INFORMATION — Electronic One Lamp

1. T-8 Electronic is available in a variety of configurations. This example describes many typical applications, for others consult factory. This application provides a two lamp ballast in the master and no ballast in the satellite. To order, add - MS11 suffix to the catalog number for master unit. Satellite does not have a ballast, thus the ballast code is changed to "X" (representing no ballast) and add - SAT suffix.

ORDERING INFORMATION — Electronic Two Lamp

1. This application provides a four lamp ballast in the master and no ballast in the satellite. To order, add - MS11 suffix to the catalog number for master unit. Satellite does not have a ballast, thus the ballast code is changed to "X" (representing no ballast) and add - SAT suffix.

ORDERING INFORMATION — Electronic Three Lamp

1. This application provides two and four lamp ballasts in the master and no ballast in the satellite, this allows switching of inboard and outboard lamps. To order, add - MS11 suffix to the catalog number for master unit. Also, the ballast code for voltage is changed to "5" for 120V or "8" for 277 volt, two electronic ballasts. Satellite does not have a ballast, thus the ballast code is changed to "X" (representing no ballast) and add - SAT suffix. The four lamp "A" ballast operates the outboard lamps and the two lamp "B" ballast operates the inboard lamps.

ORDERING INFORMATION — Electronic Four Lamp

1. This application provides two, four lamp ballasts in the master and no ballast in the satellite, this allows switching of inboard and outboard lamps. To order, add - MS11 suffix to the catalog number for master unit. Also, the ballast code for voltage is changed to "5" for 120V or "8" for 277 volt, two electronic ballasts. Satellite does not have a ballast, thus the ballast code is changed to "X" (representing no ballast) and add - SAT suffix. The four lamp "A" ballast operates the outboard lamps and the four lamp "B" ballast operates the inboard lamps.

Air diffuser—(furnished by others). All units compatible with both single and double air diffusers from all major manufacturers.

Accessory Side Air Control Blade—Adjustable for regulating volume of return air to plenum through side slots, on individual units, from below. Also adjustable for directing angle of supply air away from troffer.

Heat Transfer Dampers—Adjustable for regulating air return through lamp compartment.

Return/Supply Slots—Provide path for SUPPLY or RETURN air.

Heat Exchange (Transfer) Path—Either through slots in top of housing (Versaline) or slots in end plates (Versaline V and Parabolite III).

Job Pack

• Multiple troffers in one master carton, palletized and wrapped in plastic. Quantity per pack varies with fixture type
• Troffers can be supplied with most popular options installed
• Simplified unloading and handling
• Greatly reduced carton disposal
• Lift-off lid may be replaced to protect fixtures not immediately required
• Pallet size: 52-1/2" x 45-3/4" x x 54-3/4" high. To order, use C in the 11th digit of troffer number

Note: Click on the dimensions button to view measurements.

Distributor Stock Packs

• Available for popular stock items Troffers—2' x 4' - 20 (Regiment) Wraparound—2 lamp - 40 4 lamp - 30 (WG Series)
• Individually cartoned fixtures on pallet and stretch wrapped in plastic
• Shortens unloading and handling time
• Reduces required storage space
• Protects from damage during shipping
• Pallet size: 46-1/2" x 48-3/4" x H (height varies with fixture type; maximum is 52")

Note: Click on the dimensions button to view measurements.

Packaging Dimensions