architecture - engineering - construction
AECinfo.com
Printable version Bookmark this page Notify a colleague or friend about this page Bookmark and Share
  Hubbell Lighting Inc   Hubbell Lighting Buyers Guide\ 7 — Outdoor Lighting Products  

Square Straight Steel Poles - Page 150

   

Hubbell Lighting Buyers Guide\ 7 — Outdoor Lighting Products

hublogo.jpg (8655 bytes) Square Straight Steel Poles
SSP/SSC Series
For use with floodlight luminaires as well as post top and Magnu-Series architectural luminaires.
  • Square straight steel shaft
  • One piece construction, steel tubing
  • 2-3/8" OD tenons, or machined side mount
  • Ground lug standard (3/8'' - 16 thread)
  • Bolt template included
  • Optional removable tenon
  • Steel base
  • Two-piece base cover
  • Four L shaped galvanized anchor bolts with two nuts and two washers
  • Standard finish Lektrocote® primer
  • CSA Certified option (SSC Series)
hblo150a.gif (826 bytes)

hblo004v.gif (352 bytes)

 

ORDERING INFORMATION: SSP SERIES

hblo150b.gif (14440 bytes)

hblo150c.gif (14018 bytes)
hblo004v.gif (352 bytes)

 

ORDERING INFORMATION: SSP
hblo150d.gif (4926 bytes)

hblo150e.gif (4998 bytes)

hblo004v.gif (352 bytes)

 

ORDERING INFORMATION: CSA CERTIFIED - SSC SERIES

hblo150f.gif (15678 bytes)

hblo150g.gif (17185 bytes)

hblo004v.gif (352 bytes)

 

ORDERING INFORMATION

1. Catalog Number, as listed, does not include tenons or machining for side mounting. Desired fixture mounting must be specified by substituting for all X’s in Catalog Number.

2. Maximum allowable EPA is based on steady winds of 80 and 100 MPH with gusts to 104 and 130 MPH respectively, 120 MPH steady winds with 156 MPH gusts. All calculations are based on a minimum yield of 55,000 PSI. Calculations per AASHTO 85.

3. Factory supplied template must be used when setting anchor bolts. Hubbell Lighting will deny any claim for incorrect anchorage placement resulting from failure to use factory supplied template.

4. Anchor bolt weights not included.

Note: SSC series handhole covers have tamper resistant screws and gasket.
Note: Refer to Pole Selection Guide prior to selecting equipment.

hblo004v.gif (352 bytes)

 

SSS Series - "Slipfit"

For use with floodlight luminaires as well as post top and Magnu-Series architectural luminaires. Allows shipment on 27' ‘pup’ trucks for access to metropolitan job sites or western states. Lower 27' section plus a 3' top section with flush internal slipfit at job site. Secure with two hex head capture bolts.
  • Square straight steel shaft
  • Two piece construction, steel tubing
  • 2-3/8" OD tenons, or machined side mount
  • Ground lug standard (3/8'' 16 thread)
  • Bolt template included
  • Optional removable tenon
  • Steel base
  • Two-piece base cover Four L shaped galvanized anchor bolts with two nuts and two washers
  • Standard finish Lektrocote® primer
hblo150h.gif (1184 bytes)

 

ORDERING INFORMATION: SSS Series

hblo150i.gif (3868 bytes)

hblo150j.gif (3556 bytes)
1. Catalog Number, as listed, does not include tenons or machining for side mounting. Fixture mounting must be specified by substituting for all X’s.
2. Maximum allowable EPA is based on steady winds of 80 and 100 MPH with gusts to 104 and 130 MPH respectively, 120 MPH steady winds with 156 MPH gusts. All calculations are based on a minimum yield of 55,000 PSI. Calculations per AASHTO 85.
3. Factory supplied template must be used when setting anchor bolts. Hubbell Lighting will deny any claim for incorrect anchorage placement resulting from failure to use factory supplied template.
4. Anchor bolt weights not included.

hblo004v.gif (352 bytes)

 

Sample Catalog Number
CATALOG LOGIC

S S P - 4 10 6 - A 4 - M18
cross
section square
material
steel
base
type
shaft size square nominal
height
top type mounting arrange. fixture arm
size (holes)
options
hblo150k.gif (5045 bytes)

hblo150l.gif (7695 bytes)
hblo004v.gif (352 bytes)

 

Sample Catalog Number
CATALOG LOGIC

S S P - 4 10 6 - A 4 - M18
cross
section square
material
steel
base
type
shaft size square nominal
height
top type mounting arrange. fixture arm
size (holes)
options
hblo150m.gif (6526 bytes)
Note: See Factory Options section for illustrations and complete descriptions.

hblo004v.gif (352 bytes)

 

hblo150n.gif (8555 bytes)

 

hblo150o.gif (5430 bytes)



Request for Information / Request a Catalog from Hubbell Lighting Inc
 
 
 
To request more information from Hubbell Lighting Inc, please complete the form below.
 
*Name:    
*Email:    
Company:    
*Type:    
Phone:    
*Address:    
*Request:    
    (* = Mandatory field) 
Please add me to the mailing list for the free monthly e-Newsletter AECnews.