Tactile Concrete - Page 4

INCRETE, a wholly - owned subsidiary of INCO Chemical Supply co., occupies an ultra - modern 50,000 + square foot facility in the heart of Tampa, Florida.

Boasting worldwide network of contractors, dealers, and distributors, the INCO product line specializes in exterior decorative concrete product chemistry and design.

Recognized as a leading manufacturer in the decorative surfacing industry since 1963, INCO is continually active in its research and development programs, guaranteeing its customers state-of-the-art quality in Products, Training and Technical Services.

SEE YOUR INCRETE REPRESENTATIVE FOR:

SPECIFICATION TACTILE DETECTABLE WARNING SYSTEMS

1.0    GENERAL

This specification describes the procedural and material requirements for producing Detectable               Warning Surfaces to comply with section 4.29.2 of the Americans With Disabilities Act, by a stamping process.

1.1  STAMPING TOOL REQUIREMENTS

Stamping tools will be of both rigid and flexible design. Rigid tools will be used to apply the required surface configuration on the major portion of the specified area. Flexible tools will be used to apply the required surface on areas where a complete rigid tool will overlap the form work.

1.2  STAMPING TOOL DIMENSIONS

Both rigid and flexible tools will have overall dimensions of 24" x 36" or 24" x 48" and shall have vented openings to produce truncated domes of 0.9" diameter at the base, 0.2" in height and a centerline space of 2.35" on a triangular pitch when impressed on a fresh concrete surface.

2.0   DETECTABLE WARNING SURFACE - NEW CONSTRUCTION.

For applications where a complete new slab or ramp installation is to be installed.

2.1.1    INCO TACTILE COLOR MIX

(INTEGRAL COLOR) As manufactured by INCO CHEMICAL SUPPLY CO., INC. 8509 Sunstate St. Tampa, FI. 33634

2.1.2    INCO TACTILE COLOR HARDENER

As manufactured by INCO CHEMICAL SUPPLY CO., INC. 8509 Sunstate St. Tampa, FI. 33634

2.1.3    INCO TACTILE RELEASE

As manufactured by INCO CHEMICAL SUPPLY CO., INC. 8509 Sunstate St. Tampa, FI. 33634

2.1.4    INCO TACTILE CLEAR SEAL

As manufactured by INCO CHEMICAL SUPPLY CO., INC. 8509 Sunstate St. Tampa, FI. 33634

2.1.5   CHEMICAL REQUIREMENTS AND FORMULATION

The following requirements 0are based on a 4" thick concrete slab using 3,000 p.s.i. concrete.

TACTILE INTEGRAL COLOR(Brick Red)' 20 lbs. per cubic yard. (Other colors will require varying amounts of the Tactile Integral color)

INCO COLOR HARDENER

3.0      DETECTABLE WARNING SURFACE-RETROFIT

For applications where an existing slab or ramp must be retrofitted with a detectable warning surface contact INCO for proper procedures.

3.1  APPLICATION SPECIFICATIONS

3.1.1  INCO COLOR HARDENER - As manufactured  by INCO CHEMICAL SUPPLY CO., INC. 8509 Sunstate St. Tampa, FI. 33634

3.1.2  INCO SPRAY DECK RESIN -  As manufactured   by INCO CHEMICAL SUPPLY CO., INC. 8509 Sunstate St. Tampa, FI. 33634

3.1.3  INCO ACCELERATOR - As manufactured  by INCO CHEMICAL SUPPLY CO., INC. 8509 Sunstate St. Tampa, FI. 33634

3.1.4  INCO RELEASE AND SEALER -  As manufactured   by INCO CHEMICAL SUPPLY CO., INC. 8509 Sunstate St. Tampa, FI. 33634

3.2  COLOR

Desired color is obtained by use of the appropriate pigmentation in the Tactile Overlay Mix.

3.3 TACTILE OVERLAY MIX FORMULATION

The following proportions must be strictly adhered to in preparation of the overlay mix.

One  bag of INCO COLOR HARDENER will cover 13-15 square feet of surface area. For INCO SEALER requirements, see section 2.1.5.

INCO CHEMICAL SUPPLY CO., INC.

8509 SUNSTATE ST.

TAMPA, FL. 33634

(813) 886-8811 (800) 752-4626

FAX (813) 886-0188

©1993 INCO CHEMICAL SUPPLY CO., INC.