| GRID-MASTER™ EIFS FASTENING SYSTEM |
Product Report No.90401 |
Selector Guide
| Part No. | PIN / PLATE / FUEL PACK CONTENTS | APPLICATION | ||||||
| Plate | Qty | Pin/Nail | Qty | Fuel Cell | Wgt | EPS Thickness | Substrate | |
| 2195900 | PB10 | 1000 | 1-1/4" Pin | 1000 | 1 | 16.0 | 1" | Hollow Block, Concrete, Brick |
| 2196900 | PB15 | 1000 | 1-1/2" Pin | 1000 | 1 | 18.0 | 1-1/2" | Hollow Block, Concrete, Brick |
| 2197900 | PB15 | 1000 | 2" Pin | 1000 | 1 | 19.0 | 2" | Hollow Block, Concrete, Brick |
| 2198900 | PB10 | 1000 | 1-3/4" Nail | 1000 | 1 | 16.5 | 1", 1-1/2" | 1/2", 3/8" Plywood or Lumber |
| 2193900 | Grid-Master Tool - Complete in Plastic Case with: (2) Rechargeable Batteries; (1) Charger and A.C. Adapter; (1) Hex Key; (1) Safety Goggles; and Operator and Repair Manuals. Weight = 17 lbs. |
|||||||
Note: (1000) Fastenings per fuel cell. (8) Hour usage from fully charged battery ( Approximately 3,000 fastenings). |
||||||||
Performance Data
Pullout in Concrete / Masonry
(Smooth Shank Pin)
Average Ultimate Pounds |
|||
Pin Embedment |
|||
| 3/4" | 1/2" | 1/4" | |
| Hollow Block | 300 | 300 | 227 |
| Concrete (3M PSI Min.) |
348 | 276 | ----- |
| EPS Thickness | 1" | 1-1/2" | ----- |
| Pin Length | 1-1/4" | 1-1/2" | ----- |
Pin / Plate Pull Through
( Avg. Ultimate Pounds)
Plate Type |
|
| PB10 | PB15 |
| 300 | 350 |
Insulation / Plate Pullover
(Avg. Ultimate Pounds)
| EPS Thickness | ||
| 1" | 1-1/2" | 2" |
| 85 | 93 | 108 |
Pull Out in Wood ( Ring Shank Nail)
| EPS Thickness |
Average Ultimate Pounds | ||||
| Ext. Plywood | Lumber | ||||
| Thickness | Embedment | ||||
| 1/2" | 5/8" | 3/4" | 5/8" | 1" | |
| 1" | 122 | 166 | 256 | ---- | 222 |
| 1-1/2" | 136 | 143 | 173 | 148 | ---- |
All values are average ultimate pounds achieved under laboratory conditions. An appropriate safety factor must be applied to these values for design purpose.
GRID-MASTER™ SPACING GUIDELINES
 Pattern
A |
 Pattern
B |
Wind Load Capacity
(Average Ultimate PSF, Negative Pressure)
| 1.0 lb EPS | Pattern A | Pattern B |
| 1" | 83 | 85 |
| 1-1/2" | 105 | 104 |
* Pattern indicated and tested are based on typical, general industry guidelines. Please consult your EIFS Manufacturer for specific patterns and use of mechanical fasteners with adhesives.
* Testing was performed by Underwriters Laboratories per ASTM E330 and E331, Procedure B.
* Test data is applicable to Buildex Grid-Master Mechanical Fastening Systems only. For
additional information call Buildex Technical Services at 800-323-0720.
INSTALLATION GUIDELINES
Fastening and pullout trial tests should be made on-site to
determine optimum fastener length for the substrate conditions.
Adjust depth nosepiece to achieve proper seating of
washer.
Consult EIFS System Manufacturers' Guidelines and
recommendations for proper fastener spacings.
Always read owners manual for instruction on proper use
and safety.
 |
Grid-Master™ and Building Ideas the Work™ are registered trademarks of ITW Buildex and Illinois Tool Works Inc. |
BUILDING IDEAS THAT WORK™ 1349 West
Bryn Mawr Avenue ©1999 Illinois Tool Works, Inc. |
|
