Buildex Products Catalog (ITW Buildex)

TEKS^{^®}

SELF -DRILLING FASTENERS

Product Report No.81101

Selector Guide

	*Part Number.*	*Description*	*Head Style*	*Drill Point*	*Drill & Tap Capacity*	*Max. Material* Attachment	*Applications*
	1208200	6-20 x 3/8''	Pan	#2	.036 - .100	.100	HVAC, electrical trim accessories to steel framing. Residential steel frame construction. Track to stud. Hat channel to stud. Stud splicing.
	1210200	8-18 x 1/2''	Pan	#2	.036 - .100	.205
	1213200	8-1/ x 3/4''	Pan	#2	.036 - .100	.455
	1218200	8-1/ x 1''	Pan	#2	.036 - .100	.705
	1196200	8-1/ x 1/2''	HWH	#2	.036 - .100	.205
	1199200	8-1/ x 5/8''	HWH	#2	.036 - .100	.330
	1200200	8-1/ x 3/4''	HWH	#2	.036 - .100	.455
	1202200	8-1/ x 1''	HWH	#2	.036 - .100	.705
	1204200	8-1/ x 1-1/2''	HWH	#2	.036 - .100	1.205
	1107000 1109000 1399000	10-16 x 3/4'' 12-14 x 3/4'' 1/4-14 x 7/8''	HWH HWH HWH	#1 #1 #1	.024 - .095 .024 - .095 .024 - .095	.220 .205 .380	Stitching roof deck, wall panel sidelaps or duct work.
*Available with bonded washer.	1398000	10-16 x 1/2''	Pan	#3	.036 - .175	.150	Clips, duct straps, brick ties or accessories to steel framing.
	1541000	10-16 x 5/8''	Pan	#3	.036 - .175	.200
	1224000	10-16 x 3/4''	Pan	#3	.036 - .175	.325
	1542000	10-16 x 3/4''	Oval	#3	.036 - .175	.325
	1397000	10-16 x 1/2''	HWH	#3	.036 - .175	3150
	1127000	10-16 x 5/8''	HWH	#3	.036 - .175	.200
	1128000	*10-16 x 3/4''	HWH	#3	.036 - .175	.325
	1129000	10-16 x 1''	Oval	#3	.036 - .175	.575
	1544000	10-16 x 1''	Pan	#3	.036 - .175	.575
	1545000	10-16 x 1''	HWH	#3	.036 - .175	.575
	1130000	10-16 x 1/14''	Oval	#3	.036 - .175	.825
	1546000	10-16 x 1-1/4''	HWH	#3	.036 - .175	.825
	1131000	*10-16 x 1-1/2''	HWH	#3	.036 - .175	1.075
	1550000	10-24 x 3/4''	HWH	#3	.036 - .175	.323
	1551000	10-24 x 1''	HWH	#3	.036 - .175	.575

Performance data

PULLOUT VALUES (average lbs. ultimate)
Fastener		Steel Gauge
Dia	Pt.	26	24	22	20	18	16	14	12
#6	2	120	183	248	296	471	679	847	-
#8	2	119	193	265	298	491	703	959	-
#10	1	148	241	311	357	565	826	1111	1796
#10	3	124	208	266	299	499	708	967	1474
#12	1	159	261	338	390	649	908	1259	1949
1/4	1	208	329	428	562	800	1151

FASTENER VALUES
Fastener	Tensile (lbs.min)	Shear (avg.lbs.ult.)	Torque (min.in.lbs)
6-20	1285	750	25
8-18	1545	1000	42
10-16	1936	1400	61
10-24	2702	1500	65
12-14	2778	2000	92
1/4-14	4060	2600	150

SHEET STEEL GAUGES
Gauge No.	12	14	16	18	20	22	24	26
Decimal Equivalent	.105''	.75''	.060''	.48''	.036''	.030''	.024''	.018''

SHEAR VALUES (average lbs. ultimate)
Fastener	Steel Gauge (average lbs. ultimate)
Dia	Pt.	26	24	22	20	18	16	14
#6	2	278	466	526	758	845
#8	2	294	496	560	740	1060
#10	1	398	584	659	884	1374
#10	3				728	1266	1540	1552
#12	1	432	703	753	1018	1542
1/4	1	511	849	885	1244	1764

The values listed are ultimate averages achieved under laboratory conditions and apply to Buildex manufactured fasteners only. Appropriate safety factors should be applied to these values for design purposes.

Installation Guidelines

	A standard screwgun with a depth sensitive nosepiece should be used to install teks. For optimal fastener performance, the screwgun should be a minimum of 4 amps and have a RPM range of 0-2000.
	Adjust the screwgun nose piece to properly seat the fastener.
	New magnetic sockets must be correctly set before use. remove chip build-up as needed.
	The fastener is fully seated when the head is flush with the work surface.
	Overdriving may result in torsional failure of the fastener or stripout of the substrate.
	The fastener must penetrate beyond the metal structure a minimum of 3 pitches of thread.

Teks^®, Climaseal^® and Building Ideas the Work™ are trademarks of ITW Buildex and Illinois Tool Works Inc.

BUILDING IDEAS THAT WORK™

1349 West Bryn Mawr Avenue
Itasca, Illinois 60143
630/595-3500 FAX: 630/595-3549
www.itwbuildex.com

Teks Self Drilling Fasteners- Page 4