architecture - engineering - construction
ITW Buildex
Metal Building\Long Life Applications
Scots Trugrip - Page 8
Metal Building\Long Life Applications
| SCOTS®TRUGRIP™ |
METAL-TO-WOOD APPLICATIONS |
Product Report No. 90704 |
Selector Guide
 |
Part No. |
Description |
Drill Point |
Drill & Tap Capacity |
Max. Material Attachment |
Common
Applications |
| 1687000 1655000
1658000
1651000
1691000 |
9-15 x 1'' 9-15x1-1/2''
9-15 x 2''
9-15x2-1/2''
12-14 x 3/4'' |
Gimlet Gimlet
Gimlet
Gimlet
Gimlet |
.012-.048 .012-.048
.012-.048
.012-.048
.012-.048 |
0-.250 0-.750
.500-1.250
1.000-1.750
------ |
• Roof
and wall panel to wood
structure •
Panel over insulation to wood
structure
• Stiching of roofand wall panel |
Performance Data
| PULLOUT
VALUES IN STEEL (average lbs. ultimate) |
| Fastener |
Steel Gauge
|
| Dia |
26 |
24 |
22 |
20 |
18 |
| 9 |
171 |
252 |
329 |
401 |
634 |
| 12 |
199 |
271 |
360 |
426 |
656 |
| PULLOUT
VALUES IN WOOD (average lbs. ultimate) |
| Fastener |
Embedment
2'' x 4'' (SYP) |
| Dia |
1/2'' |
3/4'' |
1'' |
1-1/4'' |
1-1/2'' |
| 9 |
198 |
328 |
571 |
728 |
872 |
| 12 |
210 |
335 |
|
|
|
| FASTENER
VALUES |
| Fastener (dia-tpi) |
Tensile (lbs.min) |
Shear (avg.lbs.ult.) |
Torque (min.in.lbs) |
| 9 |
1800 |
1200 |
50 |
| 12 |
2778 |
2000 |
90 |
| PULLOVER
VALUES (average lbs. ultimate) |
| Fastener |
Steel Gauge |
| Dia |
|
26 |
24 |
22 |
20 |
18 |
| 9 |
Washered |
515 |
674 |
875 |
1100 |
1627 |
| 12 |
Washered |
587 |
744 |
915 |
993 |
1246 |
| SHEET
STEEL GAUGES |
| Gauge No. |
Decimal
Equivalent |
| 18 |
.048'' |
| 20 |
.036'' |
| 22 |
.030'' |
| 24 |
.024'' |
| 26 |
.018'' |
| 28 |
.015'' |
| 30 |
.012'' |
The values listed are ultimate averages achieved under
laboratory conditions and apply to Buildex manufactured fasteners only. Appropriate safety
factors should be applied to these values for design purposes.
Installation Guidelines
 |
A standard screwgun with a depth
sensitive nosepiece should be used to install Scots® TruGrip. For optimal
fastener performance, the screwgun should be a minimum of 4 amps and have a RPM range of
0-2000. |
|
Adjust the screwgun nose piece
to properly seat the fastener. |
|
New magnetic sockets must be
correctly set before use. Remove clip build up as needed. |
|
Overdriving may result in
torsional failure of the fastener or stripout of the substrate. |
|
The fastener must penetrate
beyond the metal structure a minimum of 3 pitches of thread. |
 |
Scots®,TruGrip™ GT, Climaseal® and Building Ideas the Work™ are
trademarks of ITW Buildex and Illinois Tool Works Inc. |
BUILDING IDEAS THAT WORK™ 1349 West
Bryn Mawr Avenue
Itasca, Illinois 60143
630/595-3500 FAX: 630/595-3549
www.itwbuildex.com |
©1999
Illinois Tool Works, Inc. |
|
