architecture - engineering - construction
ITW Buildex
Roofing
Hextra page 2
Roofing
| HEXTRA™ STEEL AND WOOD DECK FASTENING PRODUCT REPORT NO. 190100
Installation Guidelines
 |
An ITW Buildex Accutrac III or
an Accudrive XL PLUS installation tool, or a standard screwgun with a disengaging clutch
should be used to install Hextra fasteners. The screwgun should have a range of 1,800
-2,500 RPM. The screwgun should also have a minimum current rating of 4 amps. |
|
Fasteners should be spaced using
a pattern specified by the insulation or roof cover manufacturer. |
|
The nosepiece of the screwgun
should be adjusted so the clutch disengages when the fastener is fully and properly
seated. |
|
The fastener must penetrate the
metal deck a minimum of 3/4" for Factory Mutual System Approval. |
|
The fastener is fully seated
when the head is tight against the metal plate, or snaps into the GearLok locking plastic
plate. The fastener should not be overdriven as to cause the plate surface to deflect more
than 1/16". |
|
Overdriven fasteners will
significantly reduce fastener and plate performance and/or strip the deck. Underdriven
fasteners will not distribute the load over the plate properly. |
 |
 |
ITW Buildex Hextra
| Standard Thread |
Modified Buttress
Thread |
X-Point |
 |
| Selector Guide |
|
Hex drive
self-drilling fastener used primarily for insulation attachment to 16-26gauge steel and
wood deck. |
| Part No.(Climaseal®) |
Part No. (Spex™) |
Length |
Drive Needed |
Usable Thread Length |
Box Qty. |
| 6001006 |
6001106 |
1-5/8" |
1/4" HEX |
1-3/8" |
1000 |
| 6002006 |
6002106 |
2-1/4" |
1/4" HEX |
1-7/8" |
1000 |
| 6003006 |
6003106 |
2-7/8" |
1/4" HEX |
2-5/8" |
1000 |
| 6004006 |
6004106 |
3-1/4" |
1/4" HEX |
2-3/4" |
1000 |
| 6005006 |
6005106 |
3-3/4" |
1/4" HEX |
3-1/2" |
1000 |
| 6006006 |
6006106 |
4-3/8" |
1/4" HEX |
3-3/4" |
1000 |
| 6007006 |
6007106 |
5" |
1/4" HEX |
3-3/4" |
1000 |
| 6008006 |
6008106 |
6" |
1/4" HEX |
3-3/4" |
1000 |
| 6009006 |
6009106 |
7" |
1/4" HEX |
3-3/4" |
1000 |
| 6010006 |
6010106 |
8" |
1/4" HEX |
3-3/4" |
1000 |
| 6371910 |
1/4" Hex Socket Accutrac
III and Accudrive XL PLUS |
| 6281910 |
AccuDrive XL PLUS Installation
Tool |
Ultimate
Tensile Load - 2562 lbs.
Ultimate Shear Load - 1229 lbs. |
| Pullout Values |
In
Metal |
| Gauge |
18 |
20 |
22 |
24 |
26 |
| Lbs. |
894 |
656 |
488 |
425 |
294 |
In
Plywood |
| Thickness |
3/8" |
|
1/2" |
|
3/4" |
| Lbs. |
200 |
|
326 |
|
544 |
In
Wood Plank |
| Depth |
1" |
|
1-1/4" |
|
1-1/2" |
| Lbs. |
784 |
|
1084 |
|
1292 |
NOTE: Test results were obtained under laboratory
controlled conditions. Appropriate safety factors should be applied to these ultimate
values.
For engineering assistance or the name of your nearest ITW
Buildex distributor call toll-free 800 BUILDEX (800-284-5339).
BUILDING IDEAS THAT WORK™
1349 West Bryn Mawr Avenue
Itasca, IIIinois 60143 630/595-3500 FAX: 630/595-3569
GearLok™, SPEX™, Hextra™, Climaseal™,
Accutrac III™, Accudrive XL PLUS™, Roofgrip™ and Building Ideas That
Work™ are trademarks of ITW Buildex and IIIinois Tool Works Inc.
©1997 IIIinois Tool Works, Inc. |
