architecture - engineering - construction
ITW Buildex
Roofing
Hextra Plus page 2
Roofing
| HEXTRA PLUS™
PRE-ASSEMBLED STEEL AND WOOD DECK FASTENING PRODUCT
REPORT NO. 90703
Installation Guidelines
 |
An ITW Buildex AccuFast
installation tool, or a standard screwgun with a disengaging clutch should be used to
install the assembled fasteners. The screwgun should have a range of 1,800-2,500 RPM. The
screwgun should also have a minimum current rating of 4 amps. |
|
Fasteners should be spaced using
a pattern specified by the insulation or roof cover manufacturer. |
|
The nosepiece of the screwgun
should be adjusted so the clutch disengages when the fastener is fully and properly
seated. |
|
The fastener must penetrate the
metal deck a minimum of 3/4" for Factory Mutual System Approval. |
|
The fastener is fully seated
when the head is tight against the metal plate. The fastener should not be overdriven as
to cause the plate surface to deflect more than 1/16". |
|
Overdriven fasteners will
significantly reduce fastener and plate performance and/or strip the deck. Underdriven
fasteners will not distribute the load over the plate properly. |
ITW Buildex Hextra
| Standard Thread |
Modified Buttress
Thread |
X-Point |
 |
| Selector Guide |
*HEXTRA™
PLUS
*ROOFGRIP PLUS |
 |
Hextra
or Roofgrip fastener pre-assembled with 3" round metal plates for insulation
attachment to 18-26 gauge steel and wood. |
Hextra
Plus Part No. |
Roofgrip
Plus Part
No. |
Length |
Usable
Thread Length |
Box
Weight
(lbs.) |
Box Qty. |
| 6469003 |
6515003* |
2-1/4" |
Full |
13.5 |
250 |
| 6470003 |
6516003* |
2-7/8" |
Full |
14.6 |
250 |
| 6471003 |
6517003* |
3-1/4" |
2-3/4" |
15.1 |
250 |
| 6472003 |
6518003* |
3-3/4" |
2-3/4" |
15.8 |
250 |
| 6473003 |
6519003* |
4-3/8" |
3-1/2" |
16.7 |
250 |
| 6474003 |
6520003* |
5" |
3-3/4" |
17.8 |
250 |
| 6475003 |
6521003* |
6" |
3-3/4" |
19.1 |
250 |
| 6476003 |
6522003 |
7" |
3-3/4" |
20.7 |
250 |
| 6477003 |
6523003* |
8" |
3-3/4" |
22.1 |
250 |
*Available
with PSpex (103) long life protective coating. |
Ultimate
Tensile Load - 2562 lbs.
Ultimate Shear Load - 1229 lbs. |
Pullout Values |
In Metal |
| Gauge |
18 |
20 |
22 |
24 |
26 |
| Lbs. |
894 |
656 |
488 |
425 |
294 |
In Plywood |
| Thickness |
3/8" |
|
1/2" |
|
3/4" |
| Lbs. |
200 |
|
326 |
|
544 |
In Wood Plank |
| Depth |
1" |
|
1-1/4" |
|
1-1/2" |
| Lbs. |
784 |
|
1,084 |
|
1,292 |
NOTE: Test results were obtained under laboratory
controlled conditions. Appropriate safety factors should be applied to these ultimate
values.
For engineering assistance or the name of your nearest ITW
Buildex distributor call toll-free 800 BUILDEX (800-284-5339).
BUILDING IDEAS THAT WORK™
1349 West Bryn Mawr Avenue
Itasca, IIIinois 60143
630/595-3500 FAX: 630/595-3569
Hextra Plus™, Roofgrip Plus™,
Climaseal™ , AccuFast™ and Building Ideas That Work™ are trademarks
of ITW Buildex and Illinois Tool Work, Inc.
©1999 Illinois Tool Works, Inc. |
