1. Dry Sheathing Paper: Red rosin
paper, unsaturated.
2. Base Sheet: ASTM D 4601, Type II,
GlasBase, asphalt saturated and
coated fiber glass base sheet.
3. Base Sheet: ASTM D 4897, Type II,
Ventsulation Felt.
4. SBS Modified Bitumen Base Sheet:
DynaBase, consisting of a fiber glass
mat covered on both sides with SBS
modified asphalt.
5. Glass Fiber Felts: ASTM D 2178,
[Type VI, GlasPly Premier][Type IV,
GlasPly IV].
6. Mineral Surfaced SBS Cap Sheet:
DynaKap FR, SBS modified asphalt
roll roofing incorporating a layer of fiber
glass mat and polyester mat covered
on both sides by SBS modified asphalt
surfaced with mineral granules.
7. Mineral Surfaced SBS Cap Sheet:
DynaGlas FR, SBS modified asphalt
roll roofing incorporating a layer of fiber
glass mat covered on both sides with
an SBS modified asphalt and surfaced
with mineral granules.
8. Mineral Surfaced SBS Cap Sheet:
DynaLastic 250 FR, SBS modified
asphalt roll roofing incorporating a layer
of polyester mat covered on both sides
with an SBS modified bitumen asphalt
and surfaced with mineral granules.
9. SBS Flashing Sheet: DynaFlex, an
SBS modified asphalt roll roofing
incorporating a layer of fiber glass
scrim sandwiched between two
polyester mats, covered on both sides
by SBS modified asphalt surfaced with
mineral granules.
1. Asphalt Bitumen: ASTM D 312, Type
[III.] [IV.]
2. Concrete Primer: ASTM D 41,
Asphalt Primer.
3. Industrial Roof Cement: ASTM D
4586, Type II, cutback asphalt type.
4. Modified Flashing Cement: MBR
Flashing Cement, two-component,
elastomeric adhesive specially
formulated to be compatible with SBS
modified products.
1. Insulation: Fesco Board ASTM C
728; expanded perlite mineral
aggregate board; [_____] inch ([_____]
mm) thick; 10% Consolidation, 35 psi;
‘R’ factor of [_____]; square edges;
[factory tapered thickness;] supplied by
JM.
* * * * and/or * * * *
2. Insulation: Fiber Glass Roof
Insulation ASTM C 726 Mineral Fiber
Roof Insulation Board (Fiber Glass);
[____] inch ([___]mm) thick; square
edges; ‘R’ factor of [___]; supplied by
JM.
* * * * and/or * * * *
3. Insulation: Fesco Foam
FS-HH-I-1972/Gen and FS
HH-I-1972/3, Composite product of two
material lamination design with top
layer of polyisocyanurate foam and
bottom layer of perlite, factory bonded;
[______] inch ([_____] mm) thick;
square edges; ‘R’ factor of [_____];
supplied by JM.
* * * * and/or * * * *
4. Insulation: E’NRG’Y 2, (ASTM C
1289) polyisocyanurate rigid board;
[_____] inch ([_____] mm) thick; ‘R’
factor of [_____]; square edges;
[factory tapered thickness;] supplied by
JM.
* * * * and/or * * * *
5. Insulation: 1/2 " Retro-Fit Board,
(ASTM C 728) 1/2 inch (13 mm) high
density homogeneous panel composed
of expanded perlite blended with
selected binders and fibers, ’R’ factor
of 1.32, supplied by JM.
