TACKWALL
Lemco's tackwall provides a continuous tackable surface ideal for large display areas. It
can be provided in two ways.
- 1/4" thick material, Lemco No. 330, 320, 300F or 310 cork can be
glued directly to a smooth wall, using trowel applied adhesive. No. 37 aluminum edge trim
is recommended for all exposed edges.
- 1/2" thick wall panels Lemco No. 305, 335, 3058, or 3358, can be
provided with edges wrapped for a butt joint or No. 67 H-Bar may be used at joints. We
recommend #36 edge trim for any unfinished edges.
Specify Tackwall by selecting the desired style number and trim type
with a TW suffix added (ie. 335-TW with type two trim or wrapped edges).
NO. 310 COLORED CORK
APPLICATION: High grade linoleum resilient homogeneous tackable surface material
shall be of natural materials consisting of linseed oil, granulated cork, resin
binders and dry pigments, mixed and calendared onto a natural burlap backing. Uni-color
shall extend throughout thickness of material. Contains no harmful by-products or
carcinogens. Self healing: Linoleum cork is self healing from thumbtack and pin punctures,
does not dry out, crack, peel or crumble. Tacks can be inserted easily and are held
firmly.
SPECIFICATION:
Material: Tack surface shall be 1/4" thick burlap backed color impregnated
cork laminated to backer sheet.
Washable finish: Washable finish to retain original appearance.
Fire Resistance: A.S.T.M. E-84 (Fuel Contribution) Class B
N.F.P.A. 253 (Critical Radiant Flux) Class II
Meets Military Specification MS MIL-C-15116-C Type 1
Backing: Provide the manufacturer's specially engineered
industrial grade 1/4" inch thick high density particle board, formed and bonded with
resin creating a substrate for improved laminating. Material complies with requirements of
ANSI A208.1, grade 1-M-1. (1/4" hardboard is available but not recommended).
No. 310 - colored cork - sheet material
No. 313 - No. 310 on 1/4" industrial grade particle board
No. 311 - No. 310 on 1/4" hardboard
Sizes Available: Four and six foot widths (6'0" wide
available in Gray and tan only). Rolls approximately 90 feet long. Laminated panels are
available up to 12' long.
NO. 320 NATURAL CORK
APPLICATION: Pure granulated natural cork free from hardback, combined with
polyurethane resin binder. Density not to be less than 11 lbs. per cubic foot. Cork shall
be free from irregularities including knife marks. Tensile strength shall be in accordance
with ASTM F152. Compressibility & Recovery shall be in accordance with ASTM F36. An
economical approach to tack surfaces. Because of slight variations in thickness and
texture butt joint installation is not recommended. Meets Military Specification MS
MIL-C-15116-C Type II.
SPECIFICATION:
Material: Tack surface shall be 1/4" thick natural cork laminated to backing
sheet.
Backing: Provide the manufacturer's specially engineered
industrial grade 1/4" inch thick high density particle board, formed and bonded with
resin creating a substrate for improved laminating. Material complies with requirements of
ANSI A208.1, grade 1-M-1. (1/4" hardboard is available but not recommended).
No. 320 - Natural cork - sheet material
No. 323 - #320 on 1/4" industrial grade particle board
No. 321 - #320 on 1/4" hardboard
Sizes: Four foot widths only. Laminated panels up to 12'
long. Approximate roll size is 100'.
THIS IS A GENERAL NOTE FOR TACKSURFACES!
Tackboard Adhesive: Adhesive is used when cork sheet material is to be applied directly to
the wall. Coverage: Approximately 75 sq. ft. per gallon. TBA5 - 5 gallon container. TBA -
1 gallon container. |
