(08-2200-01)

The Interlock Relay Module shall provide three independent pairs of dry contact interlocking relay outputs. The module shall be specifically designed for two-way motion control applications. (i.e. drapery, skylights, projection screens, etc.)

Each Interlock Relay Module shall connect to the central system via a common five conductor data bus. Each module will be uniquely identified by a pair of rotary address select switches.

RELAY MODULE

(08-220-01)

The Relay Module shall be capable of providing switching control for six separately controllable loads. The module shall be designed to safely switch reactive loads such as fluorescent fixtures, motor loads, and television sets. The catch-all nature of the Relay Module also makes it ideal for switching wall receptacles.

Each Relay Module shall connect to the central system via a common five conductor data bus. Each module will be uniquely identified by a pair of rotary address select switches.

EIGHT CHANNEL RELAY MODULE

(08-2208-01)

The Eight Channel Relay Module shall incorporate features of the standard Relay Module and the Interlock Relay Module. It shall provide eight channels for switching fans, outlets, motors, low voltage incandescent, fluorescent, and other non-dimming loads.

In addition, its channels shall be able to be grouped into four independent, interlocking relay outputs for two-way motion control of drapery, skylights, etc. The module shall be able to open and close a device and to stop a device's motion mid-cycle.

The Eight Channel Relay Module shall also be able to mix the above functions as needed. For example, outputs 1 and 2 could be interlocked to control a skylight while outputs 3 through 8 act as simple power switching relays.

LOW VOLTAGE RELAY MODULE

(08-2235-01)

The Low Voltage Relay Module will be an eight channel control module with dry contact relays for low voltage. Each channel of the Low Voltage Relay Module will be an independent single pole single throw contact. The Low Voltage Relay Module is specifically intended for switching low voltage controls such as HVAC, Audio/Video, alarms, and some window treatment controls. For maximum relay life, loads should be limited to 3 amps at 24 VDC or 24 VAC.

The eight output Low Voltage Relay Module shall be powered from a Power Supply Module. Each Low Voltage Relay Module used 1/5 of a Power Supply Module's current capacity. Relay outputs are on the low voltage side and shall be intended for switching of low voltage only. This module shall require only one half of a module can space.

DC MOTOR CONTROL RELAY MODULE

(08-2240-01)

The DC Motor Control Relay shall contain 6 channels and 3 independently operated dry contact outputs. It will be used to operated two-way motion control devices powered by DC motors. It shall control both the on/off and polarity required for this control. Each of the three independent outputs shall have connections for the non-switched DC source's positive/negative connections and for each of the two motor wires. Relays shall be mounted on an external circuit board for ease of access and replacement. The DC Motor Control Module shall be powered by a LiteTouch Power Supply Module and shall require 1/5 of the power supply's current capacity.

MAINTAINED CONTACT DATA INPUT MODULE

(08-2290-01)

The Maintained Contact Data Input Module shall provide eight inputs for interfacing with non system signals such as fire alarms, security systems, RFI wireless remote, and motion sensors. Each input is primarily designed for maintained inputs and can be configured to act as almost any normal system switch including masters, timed flash masters and timed on masters. However, dimming functions will be limited to scene presets.

Each Data Input Module shall connect to the central system via the same common three conductor data bus which picks up normal system switches. Each module will be uniquely identified by a pair of rotary address select switches.

MOMENTARY CONTACT DATA INPUT MODULE

(08-2290-02)

The Momentary Contact Data Input Module shall provide eight inputs for interfacing with non system signals such as fire alarms, security systems, RFI wireless remote, and motion sensors. Each input is primarily designed for momentary inputs and can be configured to act as any normal system switch including masters, dimmers, scene presets, etc.

Each Data Input Module shall connect to the central system via the same common three conductor data bus which picks up normal system switches. Each module will be uniquely identified by a pair of rotary address select switches.

3550 South 700 West Salt Lake City, UT 84119

PH: 801.268.8668 FAX: 801.268.9200

Technical Support Line: 1.800.527.5527