Sealers, Strippers, and Cures - Page 33

QC CLEAR CURE MATTE FINISH: A lower gloss version of QC CLEAR CURE, designed to provide the optimum in curing and sealing performance with increased economy in use. Complies with V.O.C. regulations, ASTM C 309 and ASTM C 156 requirements. DIRECTIONS: Same as QC CLEAR CURE.

QC SEAL STRIP: This product is designed to quickly and efficiently emulsify and strip QC SOLVENT SEAL, QC SOLVENT SEAL V.O.C.II, QC CEMSEAL, QC SOLVENT SEAL S.D.V.O.C., QC CLEAR CURE, QC CLEAR CURE MATTE FINISH and QC COLOR CURE. DIRECTIONS: QC SEAL STRIP is water dispersible; however, it is most effective when used undiluted. Apply QC SEAL STRIP with mop or sprayer. Work small area at a time. Allow 15 minutes or longer dwell time, then scrape or scrub with a floor buffer and a stripping brush or pad. Pick up or vacuum solution, then scrub with a mild alkaline detergent solution, followed by thorough rinsing. Allow floor to dry before applying seal or finish. Approximate coverage is 100 square feet per gallon, depending on amount and type of coating.

QC INTERIOR FLOOR STRIP: Quickly and effectively strips only QC INTERIOR FLOOR SEAL and should not be used to strip or QC sealers. DIRECTIONS: Dilute with 5 to 10 parts water. Apply with mop or sprayer, allow solution to dissolve and raise old sealer for 5 to 10 minutes. Let QC INTERIOR FLOOR STRIP do the work. After scrubbing and pick up, rinse the floor and allow the to dry. Coverage is approximately 1,000 square feet per gallon.

QC FLOOR CLEANER: QC FLOOR CLEANER will clean floors sealed with QC SOLVENT SEAL, QC SOLVENT SEAL V.O.C.II, QC CLEAR CURE, QC CLEAR CURE MATTE FINISH, QC COLOR CURE, or QC INTERIOR FLOOR SEAL, without affecting the sealer coating, when used according to directions. Rinses easily without excessive foaming. DIRECTIONS: For moderately soiled floors, use 4 to 8 ounces QC FLOOR CLEANER per gallon of water. For light floor cleaning, use 1 to 2 ounces per gallon of water. For cleaning all other surfaces, concentrations can be adjusted from 1 ounce per gallon of water depending on the amount and type of soil.

QC CONCRETE DEGREASER: QC CONCRETE DEGREASER is a versatile cleaner for removing oily or greasy types of soils from colored, imprinted, and/or natural concrete floors and surfaces. Combines cleaning and degreasing without the use of petroleum solvents. However, due to its strength, it is not recommended for cleaning floors sealed with QC INTERIOR FLOOR SEAL, QC CEMSEAL, QC COLORCURE, QC CLEAR CURE, QC CLEAR CURE MATTE FINISH or other water-based sealers. For areas sealed with these products, use QC FLOOR CLEANER. DIRECTIONS: For concrete floor cleaning, add one to two cups of QC CONCRETE DEGREASER per gallon of water. Apply liberally to floor, allow ten minutes dwell time and scrub with floor machine equipped with a scrubbing or stripping pad or brush. Rinse well and allow to dry before opening to traffic or proceeding with sealer/polish application.

QC SURE TRAC: Polymeric grit coating additive designed to prevent slippery conditions if the floor seal becomes wet or oily. QC SURE TRAC can be easily mixed into both waterborne and solventborne seals. DIRECTIONS: Mix QC SURE TRAC into the sealer and stir thoroughly. Apply a medium coat of the sealer following normal application procedures using a pump-type sprayer, roller, lambswool applicator, or mop. Apply the sealer as evenly as possible, stirring frequently.

QC SEALERS, STRIPPERS and CURES are warranted to be of uniform quality within manufacturing tolerances. Since control is not exercised over its use, no warranty expressed or implied, is made as to the effects of such use. Seller's and manufacturer"s obligation under this warranty shall be limited to refunding the purchase price of that portion of the material proven to be defective. QC Construction Products, Madera, CA.

5M499