Thin Pave - Page 37

Product Information Bulletin 14.300

QC THIN-PAVE is a specially formulated polymer modified topping and fiber reinforced mix that will bond to any stable, structurally sound substrate. QC THIN-PAVE is a dry powder mixture that is integrally colored with QC THIN-PAVE COLOR PACKS (utilizing a white or gray base depending on the specific color selected) or comes pre-colored in QC THIN-PAVE PRE-COLORED MIXES. Colors can be chosen from QC's COLOR HARDENER/RELEASE POWDER Color Chart or custom colors can be produced. Most textured imprinting tools can be used when QC THIN-PAVE is installed at a 3/8" (9.5 mm) thickness. QC THIN-PAVE can also be feathered to a zero edge. QC THIN-PAVE transforms badly damaged concrete into beautiful, decorative surfaces at a fraction of the cost of removal and replacement of the existing surface. This product is extremely effective on interior applications where it's beneficial to delay the decorative concrete phase of construction until major construction is completed, reducing damage to the finished surface.

FEATURES & BENEFITS
USE INDOORS OR OUTDOORS
APPLIES TO VERTICAL AND HORIZONTAL SURFACES
DESIGNER COLORS AVAILABLE UPON REQUEST
COMPATIBLE WITH QC PATINA STAINS
FEATHERS TO A ZERO EDGE
ADHERES TO MOST ADHESIVES AND COATINGS
WIDE SELECTION OF COLORS
INCREASED TENSILE STRENGTH
EXCEPTIONAL BOND STRENGTH
MAY BE TRAFFICKED QUICKLY

DIRECTIONS FOR USE
Surface Preparation - Remove any loose/unstable paints, sealers, curing compounds, etc. or oily residues using chemical strippers, sanding, shot blasting or otherwise mechanically preparing the surface. Mechanical preparation requires no additional cleaning and is preferred. Proper cleaners should be used to ensure that any residual chemicals are entirely removed from the surface. Do not use acids. Control joints and moving / working cracks in the existing concrete are expected to transfer through the surface of the topping. Use QC CRACK REPAIR KIT after surface preparation, according to manufacturer's recommendations to bridge these types of situations and prevent the crack from appearing in the topping. When the surface is completely dry and free of residue, QC THIN-PAVE BOND COAT may be applied. Note: When a surface is found to be powdery or unstable due to improper curing, finishing, etc., apply QC CEMGUARD to harden and properly stabilize the surface. When excessive subgrade moisture/alkaline salts are present, QC CEMGUARD should also be used according to manufactures recommendations to stabilize this condition. Testing for this condition can be done by using a calcium chloride test kit. Test kits are available through most flooring distributors.

QC BOND COAT Mixing and Application Instructions - QC BOND COAT is mixed together using a 1/2" drill motor, a manufactures approved mixing paddle and mixing container/bucket or in a mortar mixer. First, add the liquid and begin mixing. Add the powder slowly while continuing to mix the liquid until a lump-free consistency is achieved. Once the material is lump-free, it is ready to apply. When applying QC BOND COAT on extremely hot days, cool the surface down by lightly misting with water. Allow the surface to completely dry before applying the QC BOND COAT Pour and spread the material using a manufacturers approved squeegee to uniformly cover the surface. Allow the QC BOND COAT to completely dry before applying the QC THIN-PAVE.

QC THIN-PAVE Mixing Instructions - Water Ratio: One gallon or less when needed per 55-pound (3.8 L per 25 kg) bag.
Uncolored Topping Mixes fixes
Mixing in buckets: Using a five-gallon (18.9 L) mixing bucket, 1/2" drill motor and an approved mixing paddle, add a single 55-pound (25 kg) bag of QC THIN-PAVE. Begin mixing one-gallon (3.8 L) of water while adding the topping mix. After approximately one-third of the bag has been added, empty the entire QC COLOR PACK into the bucket and thoroughly blend the color. Once the color is evenly dispersed, add the remainder of the bag and continue mixing for 4-6 minutes or until a lump-free consistency is achieved.
Mixing in a mortar mixer: Add the appropriate ratio of water into the mixer according to the size of the batch, while slowly adding the QC THIN-PAVE. After approximately one-third of the batch has been added, empty the entire QC COLOR PACK into the mixer and thoroughly blend the color. Once the color is evenly dispersed, add the remainder of the batch and continue mixing for 4-6 minutes or until a lump-free consistency is achieved.
Pre-colored Topping Mixes
When mixing in a mortar mixer or a bucket, add the appropriate amount of water according to the batch size. Begin mixing the water while slowly adding the pre-colored bag mix. Mix thoroughly for 4-6 minutes or until a lump-free consistency is achieved.

QC THIN-PAVE Application Instructions - Place and screed the topping mix using a manufacturer's approved gauge rake and normal concrete finishing tools to smooth the surface. When QC THIN-PAVE reaches the plastic stage of set and is ready for the final finish troweling, lightly mist the surface with water using a pump up type sprayer or squirt bottle. This will act as a lubricant to keep the finishing tools working smoothly across the surface. Do not overwork the surface, as excessive troweling may create bubbling. If the surface is to be imprinted, do so at the proper stage of set. To facilitate the release of imprinting tools, use QC RELEASE POWDER or QC LIQUID RELEASE.