Catalog No.

Power

Epcon
Cartridge 

Nozzle

E101

Manual

E6

E24, E50

E200

Pneumatic

E6

E24, E50

E300

Pneu, Dosage Control

E6

E24, E50

E400

Manual

E2

E12

Catalog No.

Volume

Nozzle

Tool

E6

17.9 Fl. Oz.

E24, E50

E101, E200, E300

E2

1.7 Fl. Oz.

E12

E400

Catalog No.

Outside Diameter

Cartridge

Tool

E12

3/8"

E2

E400

E24

1/2"

E6

E101, E200, E300

E50

11/16"

E6

E101, E200, E300

• Sturdy Carrying Case
• 1-E400 Derringer Tool
• 6-E2 Cartridges
• 12-E12 Nozzles
• 4-HB12-312 (1/2" x 3-1/2" Plated Rods with Nuts & Washers)
• 1-Information manual 

EPOXY INJECTION KIT
Catalog No. ESK400 

INSTALLATION CAUTIONS

The following cautions are applicable for installation of ITW Ramset/Red Head products:

HEAVY DUTY ANCHORS: (Trubolt Wedge, Dynabolt Sleeve, Multi-Set II Drop-In, Self-Drill, Stud, Non-Drill, Steel Deck Inset and Epcon Ceramic 6)

• WARNING: Always wear safety glasses and other necessary protective devices or apparel when installing or working with anchors.
• Maintain accurate hole size for proper installation and performance. Holes should be drilled using a bit conforming to ANSI B94.12 (except Self-Drill).
• Safe working loads for single installations under static loading should not exceed 25% of ultimate load capacity.
• Not recommended for use in lightweight masonry material such as block or brick (except for Dynabolt Sleeve Anchor and Epcon Ceramic 6).
• Not recommended for use in new concrete which has not had sufficient time to cure (except Steel Deck Insert).
• Use of core drills is not recommended to drill holes for use with these anchors (except Ceramic 6).

LIGHT DUTY ANCHORS: (Poly-Set, Tapcon, E-Z Ancor, Poly-Tie, Poly-Drive, Hammer-Set and Hammer-Loc)

• WARNING: Always wear safety glasses and other necessary protective devices or apparel when installing or working with anchors.

WARRANTY AND REMEDY
All warranties of the products described herein, express or implied, including the warranties of merchantability and fitness for particular purposes are specifically excluded, except for the following: ITW Ramset/Red Head will repair or replace at its sole option any tool part, or fastener which within twelve months after sale by ITW Ramset/Red Head or its distributors, is found by ITW Ramset/Red Head to be defective in material or workmanship, normal wear and tear excluded.
This is the sole warranty of ITW Ramset/Red Head and the sole remedy available to distributor or buyer.

LIMITATION OF LIABILITY
ITW Ramset/Red Head shall not be liable for any injury, loss or damage, direct, indirect, incidental or consequential, arising out of the use of, or the inability to use, the products described herein.

CAUTION
Failure to follow proper safety and installation procedures can result in serious personal injury or property damage.

TAPCON
*NOTE: Indicated pull-out and shear failure values were obtained in tests witnessed by Pittsburgh Testing Laboratory personnel. Designated holding power depends on the quality of the masonry material depth of embedment and proper hole size. These figures are offered only as a guide and are not guaranteed in any way by Illinois Tool Works Inc. The figures indicate average ultimate pull-out and shear failure values. A safety factor of 4:1 or 25% of ultimate pull-out value is generally accepted as a safe working load. However, reference should always be made to applicable codes for the specific safe working ratio. All values are based on close tolerance holes drilled with Ramset/Red Head Tapcon carbide drill bits. Performance of the Tapcon® anchor may vary in extremely hard concrete aggregates. Consult your Ramset/Red Head representative for further information.

As in the case with all applications, Ramset/Red Head can only suggest typical fasteners for typical applications and that the connection design is the sole responsibility of the Building Design Engineer. Architect or otherwise responsible person charged with the design of the connection. For further product information please contact the nearest Authorized Ramset/Red Head Distributor.

*NOTE: The fixture thickness being anchored and the depth of embedment in the masonry material determines the anchor length. A minimum of 1" and a maximum of 1-3/4" embedment is recommended. Hole depth must be a minimum 1/4" deeper than the anchor embedment.

Tapcon Anchors must be installed using all Ramset/Red Head system components (Tapcon Anchors, Condrive Tools, and Tapcon Drill Bits) in order to qualify for ITW Ramset/Red Head system support.

NATIONAL HEADQUARTERS AND TECHNICAL SERVICES 1300 North Michael Drive Wood Dale, IL 60191 (708) 350-0370 FAX (708) 350-7985	MANUFACTURING FACILITIES U.S. 12 & Liberty Trail Michigan City, IN 46360 Route 68 Bypass Paris, KY 40361
CUSTOMER SERVICE LOCATIONS Kennesaw (Atlanta), GA (800)241-5640 City of Commerce (Los Angeles), CA (800)368-9724 (CA only) (800)227-1823 Michigan City, IN (800)348-3231 Paris (Lexington), KY (800)354-7432	REGIONAL WAREHOUSES Kennesaw (Atlanta), GA City of Commerce (Los Angeles), CA Paris (Lexington), KY Wood Dale (Chicago), IL