Homepage  
Search
find:
search for:
   
 
Site Navigation
News / Publications
Jobs
Service
   Add this page to Google Bookmarks
   Add this page to Mister Wong
   Add this page to del.icio.us
 
   Textured Coatings of America  TEX-COTE  

TEX-COTE - Page 9

 

 

RECOMMENDED EQUIPMENT

TEX·COTE® XL-70® BRIDGE-COTE® can be either sprayed or rolled on.

  • SPRAYING: Spray equipment is Graco President 10:1 pump with Graco 204-000 spray gun or equivalent. Request an application manual for spraying TCA textured coatings.
  • ROLL ON: Standard rollers in medium and long nap, and TCA special texturing rollers.

DRYING/CURING TIMES


Times are based on ideal weather.

  • 48 Hours (To Touch)
  • 2-3 Weeks, Minimum (Final Cure)

CLEAN UP / CONTAINERS / SHELF LIFE


Clean Up

  • For wet material clean up with mineral spirits. For dry use MEK (Methyl Ethyl Ketone).

Containers

  • 5 gallon (18.9 Liters) containers, 30 (113.5 Liters) and 55 (208 Liters) gallon drums.

Shelf Life

  • Containers shall be stored upright and air tight in temperature above 40°F (4.4°C) not exceeding 100'F (37.8°C) in a dry place, avoid freezing. Any skins formed on surface of material must be removed prior to moving containers or mixing.

SURFACE PREPARATION


Surface preparation prior to the application of an applied finish coating shall consist of a general surface finish in accordance with the specific requirements of the highway department. In order to fill air pockets, honey comb, etc., surface shall be supplemented, if necessary, by the use of grout composed of one part portland cement, two parts screened and washed sand, graded to pass the 16 mesh sieve, and sufficient water to produce a thick liquid mix, or other suitable masonry patch material. The grout shall be applied using burlap pads, float sponges or other acceptable methods. As soon as grout has taken its initial set, the surface shall be brushed to remove all loose grout, leaving surface smooth and free of any air holes. Surface to be coated shall be free from efflorescence, flaking coatings, oil, release agents, curing compounds and other deleterious substances prior to the application of the applied coating. Curing compounds and release agents must be removed and may require light sandblast or waterblast.

TEX·COTE® XL-70® BRIDGE-COTE® APPLICATION RATE


XL-70 BRIDGE·COTE may be applied over green (uncured), damp or cured masonry surfaces which have been properly prepared and are clean and free of efflorescence, incompatible release agents, and curing compounds.

  • Spray/Roll On: Manufactured to meet Federal Specification TTC-5556 and the listed performance tests. A one coat application at 50 S.F. per gallon develops a minimum 15-17 mil dry film thickness.
  • The approved coverage rate for TEX·COTE XL-70 BRIDGE-COTE may vary in different states and regions. Please consult the governing agency for their requirements.

Request for Information / Request a Catalog from Textured Coatings of America
 
 
 
To request more information from Textured Coatings of America, please complete the form below.
 
*Name:    
*Email:    
Company:    
*Company type:    
Phone:    
*Address:    
*Request:    
    (* = Mandatory field) 
Please add me to the mailing list for the free monthly e-Newsletter AECnews.  
     






Printable version Bookmark this page Notify a colleague or friend about this pageHome | Terms of Use | Privacy Statement | Link to AECinfo
AECinfo is a member of Docu Group, the world's largest building products information network.



Copyright © 1996–2009 AECinfo.com