 |
Model Number Description |
CGA 120 B 3 00 B A
123 456 7 8 9,10
11 12
DIGIT 1,2,3 — Unit Type
CGA = Air-Cooled Cold Generator®
DIGITS 4,5,6 — Nominal Capacity(MBh)
100 = 8 Tons (50 Hz Model only)
120 = 10 Tons (60 Hz Model only)
150 = 12.5 Tons (50 Hz Model Only)
180 = 15 Tons (60 Hz Model Only)
DIGIT 7 — Major Design Change
(Number of Refrigerant Circuits/Number of Compressors)
B = 2 Refrigerant Circuits/2 Compressors
DIGIT 8 — Voltage
1 = 208-230/60/1 (Available — CGA120 Only)
3 = 208-230/60/3
4 = 460/60/3
W= 575/60/3
D = 380-415/50/3
DIGIT 9 — Factory Installed Options
0 = No Options
H = Hot Gas Bypass
C = Black Epoxy Coil Standard Deviation
K = Hot Gas Bypass & Black Epoxy Coil
S = Special
DIGIT 10 — Leaving Solution Setpoint
| 0 = |
Standard Expansion
Valve 40-60°F Leaving Water (CGA100 & CGA120
models)
20-60°F Leaving Solution(CGA150 & CGA180 Models) |
| V = |
Nonstandard Expansion
Valve 20-39°F Leaving Solution (CGA100 & CGA120 models) |
DIGIT 11 — Minor Design Change
A = First, B = Second, etc.
DIGIT 12 —Service Digit
20, 60 Tons
CG A F
C40 4 A A
A 1 A
12 3 4 567
8 9 10 11 12 13
DIGIT 1,2 — Unit Model
CG = IntelliPak® Air-Cooled Chiller
DIGIT 3 — Unit Type
A = Air-Cooled Condensing
DIGIT 4 — Development Sequence
F = Sixth
DIGIT 5,6,7 — Nominal Capacity
C20 = 20 Tons
C25 = 25 Tons
C30 = 30 Tons
C40 = 40 Tons
C50 = 50 Tons
C60 = 60 Tons
DIGIT 8 — Voltage & Start Characteristics
E = 200/60/3 XL
F = 230/60/3 XL
4 = 460/60/3 XL
5 = 575/60/3 XL
9 = 380/50/3 XL
D = 415/50/3 XL
S = Special
DIGIT 9 — Factory Input
A = Standard
DIGIT 10 — Design Sequence
A = First
B = Second
Etc...
DIGIT 11 — Leaving Solution Setpoint
A = 40-50 Deg. F w/o Ice Machine
B = 30-39 Deg. F w/o Ice Machine
D = 51-65 Deg. F w/o Ice Machine
E = 20-29 Deg. F w/o Ice Machine
1 = 40-50 Deg. F with Ice Machine
2 = 30-39 Deg. F with Ice Machine
3 = 51-65 Deg. F with Ice Machine
4 = 20-29 Deg. F with Ice Machine
S = Special
DIGIT 12 — Agency Approval
1 = UL/CSA
0 = None
DIGIT 13 — Miscellaneous
A = Trane Communication Interface (TCI) Module
B = No Unit Heat Tape (50 Hz Only)
C = Compressor Current Sensing (CSM)
D = Unit Mounted Disconnect Switch Nonfused
E = Unit Isolators Neoprene
F = Unit Isolators Spring
G = Superheat/Sub-Cooling
H = Hot Gas Bypass
J = Generic B A S Module
(0-5 v Input, Binary Output)
M = Remote Human Interface
N = Generic B A S Module
(0-10 v Analog)
P = Remote Setpoint Potentiometer
Q = Zone Sensor — Chilled Solution Reset
R = Phase/Voltage Monitoring
T = Flow Switch
V = Copper Fin Condenser Coils
W= Electronic Low Ambient Damper(s)
Y = Inter-Processor Communication Bridge (IPCB)
9 = Packed Stock Unit
The following items can be ordered for separate shipment
—
Unit Isolators — Neoprene*
Unit Isolators — Spring*
Flow Switch
Electronic Low Ambient Damper(s)
Trane Communication Interface Module (TCI)
Generic B A S Module (GBAS) (0-5 volt Analog Input/Binary
Output)
Generic B A S Module (GBAS) (0-10 volt Analog Input/Output)
Remote Human Interface
Remote Setpoint Potentiometer
Zone Sensor (Chilled Solution Reset)
Inter-Processor Communication Bridge (IPCB)
*Unit size must be specified when ordering this item. |
