 |
Model Number
Description |
|
| S |
X |
H |
G |
D11 |
4 |
0 |
A |
H |
7 |
C |
F |
8 |
D |
3 |
0 |
0 |
1 |
Y |
| 1 |
2 |
3 |
4 |
567 |
8 |
9 |
10 |
11 |
12 |
13 |
14 |
15 |
16 |
17 |
18 |
19 |
20 |
21 |
DIGIT 1 — UNIT TYPE
S = Self-Contained (Packaged Rooftop)
DIGIT 2 — UNIT FUNCTION
E = DX Cooling, Electric Heat
F = DX Cooling, Natural Gas Heat
L = DX Cooling, Hot Water Heat
S = DX Cooling, Steam Heat
X = DX Cooling, No Heat, Extended Casing
DIGIT 3 — UNIT AIRFLOW
H = Single Zone
DIGIT 4 — DEVELOPMENT SEQUENCE
G = Seventh
DIGITS 5,6,7 — NOMINAL CAPACITY
C90 = 90 Tons
D11 = 105 Tons
D12 = 115 Tons
D13 = 130 Tons
DIGIT 8 — POWER SUPPLY
4 = 460/60/3 XL
5 = 575/60/3 XL
E = 200/60/3 XL
F = 230/60/3 XL
DIGIT 9 — HEATING CAPACITY
0 = No Heat
H = High Heat - 2-Stage
J = High Heat - Limited Modulation
P = High Heat - Full Modulation
Note: When the second digit calls for "E"
(electric heat), the following values apply in the ninth digit:
W = 190 KW
When the second digit calls for ‘’L’’
or ‘’S’’, one of the following valve size values must be in Digit 9:
High Heat Coil: 3 = 1.0", 4 = 1.25", 5 =
1.50", 6 = 2.0", 7 = 2.5"
Low Heat Coil: C = 1.0", D = 1.25", E =
1.50", F = 2.0", G = 2.5"
DIGIT 10 — DESIGN SEQUENCE
A = First (Factory Assigned)
Note: Sequence may be any letter A thru Z.
DIGIT 11 — EXHAUST OPTION
0 = None
7 = 100%, 15 HP W/Statitrac
8 = 100%, 20 HP W/Statitrac
9 = 100%, 25 HP W/Statitrac
F = 50%, 15 HP
H = 100%, 30 HP W/Statitrac
J = 100%, 40 HP W/Statitrac
K = 100%, 15 HP W/O Statitrac (CV Only)
L = 100%, 20 HP W/O Statitrac (CV Only)
M = 100%, 25 HP W/O Statitrac (CV Only)
N = 100%, 30 HP W/O Statitrac (CV Only)
P = 100%, 40 HP W/O Statitrac (CV Only)
DIGIT 12 — EXHAUST AIR FAN DRIVE
0 = None
5 = 500 RPM
6 = 600 RPM
7 = 700 RPM
8 = 800 RPM
DIGIT 13 — FILTER
A = Throwaway
C = High-Efficiency Throwaway
D = Bag With Prefilter
E = Cartridge With Prefilter
F = Throwaway Filter Rack Less Filter Media
G = Bag Filter Rack Less Filter Media
DIGIT 14 — SUPPLY AIR FAN HP
C = 30 HP (2-15 HP)
D = 40 HP (2-20 HP)
E = 50 HP (2-25 HP)
F = 60 HP (2-30 HP)
G = 80 HP (2-40 HP)
DIGIT 15 — SUPPLY AIR FAN DRIVE
5 = 500 RPM
6 = 600 RPM
7 = 700 RPM
8 = 800 RPM
9 = 900 RPM
DIGIT 16 — FRESH AIR
D = 0-100% Economizer (Std.)
DIGIT 17 — SYSTEM CONTROL
1 = Constant Volume Control
2 = VAV Supply Air Temperature Control w/o Inlet Guide
Vanes
3 = VAV Supply Air Temperature Control w/ Inlet Guide Vanes
4 = Space Pressure Control with Exhaust VFD w/o Bypass
5 = Space Pressure Control with Exhaust VFD and Bypass
6 = VAV Supply Air Temperature Control with VFD w/o Bypass
7 = VAV Supply Air Temperature Control with VFD and Bypass
8 = Supply and Exhaust Fan with VFD w/o Bypass
9 = Supply and Exhaust Fan with VFD and Bypass
DIGIT 18 — ACCESSORY PANEL
0 = None
A = BAYSENS008*
B = BAYSENS010*
C = BAYSENS013*
D = BAYSENS014*
E = BAYSENS019*
F = BAYSENS020*
G = BAYSENS021*
DIGIT 19 — AMBIENT CONTROL
0 = Standard
DIGIT 20 — AGENCY APPROVAL
0 = None (UL Gas Heater, see note)
1 =UL
2 = CSA
Note: Includes UL classified gas heating section only, when
second digit of Model No. is a "F."
DIGIT 21 — MISCELLANEOUS
A = Unit Disconnect Switch
B = Hot Gas Bypass (CV Only)
D = Comparative Enthalpy
E = Low Leak Fresh Air Dampers
F = High Duct Temperature Thermostat
G = High Capacity Evaporator Coil
(90-105 Only)
J = BAYSENS016*
K = Generic B.A.S. Module
L = High-Efficiency Motors (Supply
and Exhaust)
M = Remote Human Interface
N = Ventilation Override Module
P = BAYSENS017*
R = Extended Grease Lines
T = Access Doors
U = BAYSTAT023*
V = Inter-Processor Communication Bridge
Y = Trane Communication Interface Module
3 = BAYMTPL003
4 = BAYMTPL004
5 = VFD Line Reactor
6 = Factory-Powered 15A GFI Convenience Outlet
EXAMPLE:
Model numbers: SXHGD1140AH7CF8D3001Y describes a unit with
the following characteristics: DX cooling with extended casing, no heat, 105 ton nominal
cooling capacity, 460/60/3 power supply, no heat, 100 percent exhaust with
Statitrac, 30 h.p. exhaust fan motor with drive selection No. 7 — (700 RPM),
high-efficiency throwaway filters, 60 hp supply fan motor with drive selection No. 8
— (800 RPM), economizer, VAV supply air temperature control with inlet guide vanes,
no remote panel, standard ambient, UL agency approval, and Trane Communication Interface
Module. |
