| Hurricane Ties - HA, HT 
| |
|
|
|
|
|
ALLOWABLE
UPLIFE LOADS |
| |
|
|
|
FASTENERS |
WHEN
FASTENED TO: |
| PRODUCT |
GAUGE |
W |
H |
TRUSS |
STUD |
22ga |
20ga |
18ga |
16ga |
14ga |
| HA2 |
18 |
1-1/2 |
9 |
4 |
5 |
385 |
385 |
385 |
385 |
385 |
| HA9 |
18 |
1-9/16 |
2 |
4 |
4 |
520 |
520 |
520 |
520 |
520 |
| HA10 |
18 |
1-9/16 |
6-3/4 |
4 |
4 |
650 |
880 |
1150 |
1150 |
1150 |
| HA10-2 |
18 |
3-1/16 |
6-3/4 |
4 |
4 |
650 |
880 |
1150 |
1150 |
1150 |
| HT6 |
16 |
2-1/4 |
20 |
4 |
4 |
650 |
880 |
1310 |
1410 |
1410 |
| HA4L/R |
18 |
2-1/4 |
4-1/2 |
3 |
3 |
475 |
475 |
475 |
475 |
475 |
| HT1 |
18 |
1-9/16 |
5-1/4 |
4 |
4 |
540 |
540 |
540 |
540 |
540 |
Uplift loads have been increased 1/3 for wind or
earthquake. No further increase is allowed.
PRODUCT FEATURES
- These hurricane and seismic anchors add resistance to wind
uplift and earthquake lateral loads, by utilizing correctly located screw holes for fast,
easy, economical and strong attachment of rafters and trusses to studs and track.
- Fabricated of 18 and 16 gauge steel.
INSTALLATION
- Use all specified fasteners in schedule to achieve values
listed.
- Products which tie the truss or rafter to the stud below may
be installed on either side of the wall or they may be installed on both sides of the wall
for twice the load resistance.
|
Embedded Truss Anchors - ETA
|
|
NUMBER
OF #10 SCREWS NECESSARY |
| TO
ACHIEVE MAXIMUM LOAD |
|
|
|
|
MAXIMUM
LOADS |
WHEN
FASTENED TO |
WHEN
WRAPPED |
| F1 |
F2 |
STUD |
TRUSS |
WALL
STUD |
OVER TOP OF
TRUSS |
| PRODUCT |
H1 |
H2 |
|
|
UPLIFT |
UPLIFT |
20ga |
18ga |
16ga |
14ga |
12ga |
(FOR ALL
GAUGES) |
| ETA12 |
8 |
12 |
110 |
240 |
1410 |
700 |
6 |
4 |
3 |
3 |
2 |
3 |
| ETA14 |
10 |
14 |
110 |
240 |
1680 |
700 |
8 |
5 |
4 |
3 |
3 |
3 |
| ETA16 |
12 |
16 |
110 |
240 |
1680 |
700 |
8 |
5 |
4 |
3 |
3 |
3 |
| ETA18 |
14 |
18 |
110 |
240 |
1680 |
700 |
8 |
5 |
4 |
3 |
3 |
3 |
| ETA20 |
16 |
20 |
110 |
240 |
1680 |
700 |
8 |
5 |
4 |
3 |
3 |
3 |
| ETA22 |
18 |
22 |
110 |
240 |
1680 |
700 |
8 |
5 |
4 |
3 |
3 |
3 |
Uplift loads as well as lateral loads have been
increased 1/3 for wind or earthquake. No further increase is allowed.
PRODUCT FEATURES
- Accommodates diverse design requirements for concrete to
steel installation. Requires only 4" embedment in concrete.
- Concrete compressive strength is minimum of 2000psi.
- 18 gauge galvanized steel.
- Other sizes available.
INSTALLATION
- Use specified fasteners from schedule to achieve maximum
load.
- When an ETA is used on a truss, the ETA must be installed so
it wraps over the top chord of the truss as shown.
- When ETA is wrapped over the top of the truss, two screws
are to be applied on the side of the ETA that is embedded while one screw is to be applied
on the opposite side.
- Two anchors may be installed, one on each side of
truss, for twice the load resistance.
|
Universal Framing Angles - UFA, UFAF
| |
|
|
NUMBER OF
SCREWS ON EACH FLANGE |
|
|
| |
|
|
NECESSARY
WHEN FASTENED TO: |
ALLOWABLE
LOADS |
| PRODUCT |
FASTENERS |
LOAD |
22ga |
20ga |
18ga |
16ga |
FLOOR & ROOF |
UPLIFT |
| UFA |
#10 Screws |
F1 |
5 |
4 |
3 |
3 |
560 |
745 |
| UFAF |
#10 Screws |
F2 |
5 |
4 |
3 |
3 |
575 |
765 |
Uplift loads have been increased 1/3 for wind or
earthquake. No further increase is allowed.
PRODUCT FEATURES
- Multipurpose anchor can be used as a joist connector,
tension tie, shear connector and universal framing angle.
- Accurately fastens joists to headers, joists to track, track
to rim joists, and fastens blocking to framing members.
- When used as joist connector, they should be installed in
pairs, one on each side of the joist.
- 18 gauge galvanized steel.
- Use the quantity of specified fasteners from the schedule to
achieve desired loads.
|
|
